民间美术论文doc.doc

  1. 1、本文档共18页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
民间美术论文doc

河南大学自学考试本科毕业论文 民间美术在中小学美术课中的应用 作 者 李 垒 专 业 美术教育 准 考 证 号 110108150832 成 绩 _____________ 联 系 电 话工 作 单 位 河南省漯河市天一教育中心 完 成 时 间 2010.8 民间美术在中小学美术课中的应用 摘要:民间美术民间美术植根于祖国大地,来源于大众的生活,是广大劳动人民创造务大众成各民族传统的重要组成部分,具有鲜明的民族文化特征民间美术是以美化环境丰富民间风俗活动为目的,在日常生活中应用流行的美术。它表达了人民群众的心理愿望信仰和道德观念,世代相沿且又不断创新发展,成为民族乡土特色的优美艺术形式。民间美术有其独特的文化特征与审美特征,这些特征: 第一民间美术的内容是理想主义的。十卷206页 the same direction of rotation 90 ° or 180 ° for; after each disc rotor when measuring position alignment of the two half coupling constant, should also be in terms of accuracy and consistency. Surface deviation measurement, must in every 180 degrees corresponding to the two radii are equal to each other in order to eliminate errors caused by movement of the rotor. Only a support bearing of the rotor, WA couplings, such as the use of temporary leave the Center, should pay attention to keep the rotor in the measuring process in the center of the bearing oil retaining the nest does not change. Steam oil block, there should be sufficient clearance between the rotor and, in rotors make sure rotor is not on the block or seal oil. At the time of measurement, connections are not allowed between two rotors, each in a free State. Not allowed in case of assembled sleeve, Center work on the toothed coupling. Coupling tool should have adequate stiffness, installation must be secure and reliable. Coupling Center using a dial indicator, the table should be put in prison and avoid touching, to ensure correct measurement. Coupling disc after a week to return to the original position, circumference of dial gauge reading should be able to go back to the original value. When measuring the clearance of end, into the feeler of the gap should not exceed four at a time, when the gap is too large, you can use the gasket with the feeler gauge measurement of gauge blocks or finishing. bearing surface, markup should be in accordance with the mounting sup

文档评论(0)

jiaoyuguanliji + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档