高密度聚乙烯双壁波纹管管道设计、施工技术规程(国外英文资料).docVIP

高密度聚乙烯双壁波纹管管道设计、施工技术规程(国外英文资料) In this paper, by zhaojing188 contribution Doc documents may have a poor browsing experience at the WAP end. It is recommended that you choose TXT, or download the source file to the native view. High density polyethylene double wall corrugated pipe design, high density polyethylene double wall corrugated pipe design, construction technology discipline pipeline design 1 general 1.0.1 hdpe double-wall corrugated pipe (CPP) (hereinafter referred to as the double-wall corrugated pipe) is a new type of drainage pipe. In order to outdoor buried drainage pipeline engineering design, construction and acceptance, to achieve the advanced technology, reasonable economy, ensure the engineering quality, this law is enacted regulations. 1.0.2 these procedures shall apply to new, expansion, and reconstruction of outdoor buried hdpe double-wall corrugated pipe drainage (CPP) engineering design, construction and acceptance. 1.0.3 these procedures shall apply to outdoor buried pipe diameter DN800mm under high density polyethylene double-wall corrugated pipe (CPP). 1.0.4 applied in this discipline, into the pipe of the water temperature should be not more than 40 oc; 排放管道的水质,应符合《污水排入城 市下水道水质标准》(CJ18-86)的规定. 1.0.5 本规程可用于埋设在一般地质条件下或酸,碱性等腐蚀性土壤中. 1.0.6 施工人员应按设计文件和施工图施工.遇本规程未涉及的问题或有特殊要求时,变更设 计应经设计单位同意. 1.0.7 管道工程用的管材,管件,密封圈,等必须符合现行的国家和行业产品标准. 1.0.8 除执行本规程外,尚应符合国家现行的标准和行业标准及本地区的有关规定. 1.0.9 执行本规程时,必须遵守国家和地方的有关安全,劳动保护,防火,环保等方面的有关 规定. 2 引用标准 GBJ 14-87(1997 年版)室外排水设计规范 GBJ 69-84 给水排水工程结构设计规范 GB 50268-97 给水排水管道工程施工及验收规范 CJJ 3-90 市政排水管渠工程质量检验评定标准 3 术语 3.0.1 双壁波纹管 corrugated pipe 管壁截面为双层结构,内壁的表面光滑,外壁为等距排列的环形中空波纹结构的管材. 3.0.2 公称内径(de)norminal inside diameter 为便于应用,对热塑性塑料管系统管材以内径标定. 注:本规程中公称内径与管材实际内径等同(个别规格以外径定径,公称直径为外径). 3.0.3 最小内压强度 minimum internal pressure strength 指无压重力流排水管道,在 50 年长期输水条件下,对使用的管道进行内压检验,耐内压强度 最低界限的规定. 3.0.4 环刚度 ring stiffness 管材试件在两平板压扁至管内径垂直方向的变形为规定值时所施加的单位长度垂直荷载的换算 值.用以衡量管材承受外压荷载的能力,而无实际的物理学意义. 3.05 弹性直径变形率 elastic diameter deformation rate Under