宝马正时调整(国外英文资料).docVIP

下载本文档

7
0
约 19页
2017-06-12 发布于河南
举报
版权申诉

宝马正时调整(国外英文资料).doc

1、本文档共19页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

宝马正时调整(国外英文资料)

宝马正时调整(国外英文资料) How to adjust the author: auto repair special tool 12, 525i / 528i (E28) (engine no. 25 6E A, 28 6E C) (1981-1987); 530i / 535i (E34) (engine no. 30 6K A, 34 6E C, 34 6K B) (1981-1993) (1) the adjustment procedure for the valve timing The engine stops at 1 on the first cylinder. The camshaft sprocket thread hole is perpendicular to positive (see figure 2). The camshaft sprocket is positioned in position 3. Remove tension plug 4. Note: ce4 is compressed by a strong spring. Remove the camshaft sprocket. As shown in figure 2-2-88. 13, 530i / 540i V8 (E34) (engine no. 30 8S 1,408s 1) (1992-1996); 730i / 740I (E32) (engine no. 30 8S 1,408s 1) (1992-1994) (1) the adjustment procedure for the valve timing The engine stops on the first cylinder. Insert the flywheel and pin 1. Tool number 11, 2, 300. Make sure that the first cylinder has a convex Angle 2 opposite. Make sure the camshaft sprocket arrow 3 up. Install the camshaft alignment tool 4. Tool number 11, 2, 441/442/443/444/445. Before tightening the camshaft sprocket bolt, give the timing chain pretension. Use the tool 11, 3390 (see figure 5). As shown in figure 2-2-89. 14, 535I (E39) (engine no. 358s 1 (M62)) (1996-2000); 735I (E38) (engine no. 358s 1 (M62)) (1996-2000) (1) the adjustment procedure for the valve timing Disassemble/install the timing chain needs: · remove the oil tray. The engine stops on the first cylinder. Insert the flywheel and pin 1. Make sure the first cylinder has a convex Angle of two opposite. Make sure the sensor is marked on location 3. Install the camshaft alignment tool 4. Use wrench 5 to prevent the camshaft rotation in the diagram location. The secondary tensioner is able to lock with tool 6. Install the chains exhaust CAM shaft sprocket 7 in the following order: · make sure the hole is at the center of the groove. · release the secondary tenser. Install the exhaust camshaft sprocket bolts 7 (dont screw up). Install the chain of inlet camshaft sprocket with the chain in t