3512发动齿条同步, 单体泵和气门调整程序.pptVIP

Caterpillar 3512 Engine Adjustment卡特彼勒3512发动机调整程序 3512Engine Design发动机设计 3512Engine Specification3512发动机技术规范 Fuel Injection Control Linkage单体泵连动杆装置 Fuel Injector Synchronization Procedure单体泵齿条同步行程调整程序-1 Fuel Injector Synchronization Procedure单体泵齿条同步行程调整程序-2 Fuel Injector Synchronization Procedure单体泵齿条同步行程调整程序-3 Fuel Injector Synchronization Procedure单体泵齿条行程同步调整程序-4 Top Center Position for the No. 1 Piston寻找活塞在第1缸上止点-1 Top Center Position for the No. 1 Piston寻找活塞在第1缸上止点-2 Top Center Position for the No. 1 Piston寻找活塞在第1缸上止点-3 Valve Lash and Valve Bridge Adjustment气门和气门桥调整工具 Valve Bridge Adjustment气门过桥调整程序-1 Valve Bridge Adjustment气门过桥调整程序-2 Valve Bridge Adjustment气门过桥调整程序-3 Valve Lash Adjustment Specification气门间隙调整规格 Valve Lash Adjustment气门间隙调整程序-1 Valve Lash Adjustment气门间隙调整程序-2 Valve Lash Adjustment气门间隙调整程序-3 Fuel Injector Timing Tool单体泵正时调整工具 Fuel Injector Timing Tool单体泵正时调整工具-1 Fuel Injector Timing Tool单体泵正时调整工具-2 Fuel Injector Timing Tool单体泵正时调整工具-3 Fuel Injector Timing单体泵正时调整程序-1 Fuel Injector Timing单体泵正时调整程序-2 Fuel Injector Timing单体泵正时调整程序-3 Fuel Injector Timing单体泵正时调整程序-4 * 1.单体泵齿条同步行程调整程序 2.寻找活塞在第1缸上止点 3.气门过桥调整程序 4.气门间隙调整程序 5.气门和气门桥调整工具 6.单体泵正时调整程序 CH Yeap. June16,2006 秧逸却碳枣上伦痞阳弹谓创玲沃螟焊椅守观涨扑莫诽拨嚼攘删酪剔拂廉悬3512发动齿条同步, 单体泵和气门调整程序3512发动齿条同步, 单体泵和气门调整程序 进气门 排气门 发动机组名牌位置 梆传蹭末概锤困食交篡宇冶虏桨据话堆稀汀篓铭合痰狗因伟脂俺柞婶玖妥3512发动齿条同步, 单体泵和气门调整程序3512发动齿条同步, 单体泵和气门调整程序 3512 Crankshaft Position for Fuel Injector Adjustment and Valve Lash Setting 3512单体泵和气门阀调整顺序 Counterclockwise rotation –CCW. (Standard) from the flywheel end of the engine 面向飞轮曲轴转动方向逆时针方向运转(标准运转) No. 1 Piston At Top Center Position 活塞在第1缸上止点 No. 11 Piston At Top Center Position 活塞在第11缸上止点 Inlet Valves 空气进气阀 1-3-6-7-10-12 2-4-5-8-9-11 Exhaust Valves 排气阀 1-4-5-6-9-12 2-3-7-8-10-11 Injectors 单体泵 2-4-5-8-9-11 1-3-6-7-10-12 Standard rotation CCW 标准逆时针方向运转点火顺序 Inlet 进气阀调整 Exhaust 排气阀调整 1, 12, 9, 4, 5, 8, 11, 2, 3, 10, 7, 6 0.50 mm (0.020 inch) 1.00 mm (0.040 inch) 慷畅郴织特皂波乡韭卉傣率晰桨都羹叫检陕挤岂像缉癣见卫改教无蒋侦着35