关于STM3F103RC芯片对EEPROM 芯片AT24C64的IIC通信.docVIP

关于STM32F103RC芯片对EEPROM 芯片AT24C64的IIC通信文档说明：本文档仅提供最基础的操作函数，包含四个函数分别为：void I2C_EEPROM_WriteByte(unsigned short WordAddress)，此函数是对EEPROM进行一次随机地址写一个字节数据操作。void I2C_EEPROM_WritePage(unsigned short WordAddress, unsigned char *data, unsigned int length)，此函数是对EEPROM进行指定起始地址连续写N个数据。unsigned char I2C_EEPROM_ReadByte(unsigned short WordAddress)，此函数是对EEPROM进行随机地址读取一个字节数据。void I2C_EEPROM_SeqReadByte(unsigned short WordAddress, unsigned char* array, unsigned int number)，此函数是对EEPROM进行随机首地址连续读取N个数据。#define I2C1_SLAVE_ADDRESS7 0xA0 // AT24C64 Device address#define I2C_Speed 100000 //IIC速率为100K函数中加入了延时等待，这样做是为了防止程序卡死某处，而不使整个工程程序无法运行下去。函数中有I2C1_TIME是延时时间设置，可调整。如果I2C1_TIME没有调整好恐怕程序无法正常运行。建议设置I2C1_TIME为200，一般是往大调，可根据实际情况调整。这个可能比较费时，需要有耐心哦！这些是经过实际测试过的。我个人认为STM32 IIC 不好用就在于时序可能有点问题，如果说起始很好的话一般都能运行下去，我就经常卡在开始的忙检测上，有时忙标志经常为1，所以条件状态过不去。还有就是不管是读还是写，两个函数不要连续，最好中间隔一段时间。要不然总线时序会乱的。以上经供参考，不要过于认真哦！有不对之处请批评指正，谢谢！////Function Name: void I2C_EEPROM_WriteByte(unsigned short WordAddress)//Function Discription: write byte data to AT24C64 //Function Parameters: // INPUT: Random WordAddress// OUTPUT://Return Value: //void I2C_EEPROM_WriteByte(unsigned short WordAddress, unsigned char data){ unsigned int ui_cnt, ui_stateflag; ui_cnt = I2C1_TIME; I2C_AcknowledgeConfig(I2C1, ENABLE); do { ui_stateflag = I2C_GetFlagStatus(I2C1,I2C_FLAG_BUSY); } while ((ui_stateflag == SET) (-- ui_cnt)); if(ui_stateflag == RESET) { ui_stateflag = ERROR; I2C_GenerateSTART(I2C1,ENABLE); ui_cnt = I2C1_TIME; do { ui_stateflag = I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_MODE_SELECT); } while ((ui_stateflag == ERROR) (-- ui_cnt)); if(ui_stateflag == SUCCESS) { ui_stateflag = ERROR; I2C_Send7bitAddress(I2C1,I2C1_SLAVE_ADDRESS7,I2C_Direction_Transmitter); ui_cnt = I2C1_TIME; do { ui_stateflag = I2C_CheckEvent(I2C1,I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED); }while((ui_stateflag == ERROR) (-- ui_cnt)); if(ui_stateflag == SUCCESS) { ui_stateflag = ERROR;