微机测速.docVIP

#include REG52.H #define uchar unsigned char #define uint unsigned int #define ulong unsigned long #define LED_DAT P0 #define LED_ON() P3^0 = 0; #define LED_OFF() P3^0 = 1; //sbit out=P1^4; sbit beep=P2^3; sbit LED_SEG0 = P2^7; sbit LED_SEG1 = P2^6; sbit LED_SEG2 = P2^5; sbit LED_SEG3 = P2^4; //sbit pin_SpeedSenser = P3^5; //光电传感器信号接在T1上 #define TIME_CYLC 100 //12M晶振，定时器10ms 中断一次 我们1秒计算一次转速 // 1000ms/10ms = 100 4444 #define PLUS_PER 6 //码盘的齿数 ，这里假定码盘上有6个齿，即传感器检测到6个脉冲，认为1圈 4444444444 #define K 74.0 //校准系数 uchar low=40; uchar high=55; uchar lowset[2]; uchar highset[2]; uint speed=0; uchar once=0; unsigned char code table[]= {0x28,0xEB,0x32,0xA2,0xE1,0xA4,0x24,0xEA,0x20,0xE0}; uchar data Disbuf[4];// 显示缓冲区 uint Tcounter = 0; //时间计数器 bit Flag_Fresh = 0; // 刷新标志 bit Flag_clac = 0; //计算转速标志 bit Flag_Err = 0; //超量程标志 unsigned char key; unsigned char KeyScan(void); void Delay_ms(unsigned int n); void Beep(void); //在数码管上显示一个四位数 void DisplayFresh(); //计算转速，并把结果放入数码管缓冲区 void ClacSpeed(); //初始化定时器T0 void init_timer0(); //初始化定时器T1 void init_timer1(); //延时函数 void Delay(uint ms); void it_timer0() interrupt 1 /* interrupt address is 0x000b */ { TF0 = 0; //d定时器 T0用于数码管的动态刷新 // TH0 = 0xe0; /* init values *///c TL0 = 0x00; Flag_Fresh = 1; Tcounter++; if(TcounterTIME_CYLC) { Flag_clac = 1;//周期到，该重新计算转速了 } } void it_timer1() interrupt 3 /* interrupt address is 0x001b */ { TF1 = 0; //定时器T1用于单位时间内收到的脉冲数 //要速度不是很快，T1永远不会益处 Flag_Err = 1; //如果速度很高，我们应考虑另外一种测速方法，：脉冲宽度算转速 } void main(void) { uchar i=0; Disbuf[0] = 0; //开机时，初始化为0000 Disbuf[1] = 0; Disbuf[2] = 0; Disbuf[3] = 0; init_timer0(); init_timer1(); while(1) { key=KeyScan(); if(key!=0xff)//有键按下 { if(key==10) { while(KeyScan()!=0xff);//手离开 for(i=0;i2;i++) { while(KeyScan()==0xff); lowset[i]=KeyScan(); while(KeyScan()!=0xff); } low=lowset[0]*10+lowset[1]; while(KeySca