网站大量收购独家精品文档,联系QQ:2885784924

约克工业冷冻用户培训课程.ppt

  1. 1、本文档共49页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
约克工业冷冻用户培训课程资料

约克工业冷冻机组部件 介绍-油分离器 约克工业冷冻机组部件 介绍-凝聚段過濾器 雙油過濾器,可在不停机的情況下更換過濾器。 约克工业冷冻机组部件 介绍-油過濾器 约克工业冷冻机组部件 介绍-过滤器滤芯 约克工业冷冻机组件 介绍-油泵 預潤滑油泵 循環全潤滑油泵 全潤滑油泵 无油泵-冷启动阀 约克工业冷冻机组件 介绍-冷启动阀 约克工业冷冻机组部件 介绍-油冷卻方式 水冷式油冷卻器 熱虹吸式油冷卻器 噴液式油冷卻器 空冷式油冷卻器 直接膨脹式油冷卻器 约克工业冷冻机组部件 介绍-水冷式油冷 约克工业冷冻机组部件 介绍-水冷式油冷 热虹吸式油冷 约克工业冷冻机组部件 介绍-經濟器 經濟器是對來自冷凝器的液体在進入蒸發器之前經過一個熱交換器, 使過冷液体進蒸發器,以提高系統容量和效率,另一部分制冷劑進入壓縮机經濟器接口繼續壓縮,該熱交換器被稱為經濟器。 經濟器有多种:殼管式、直接膨脹式和閃發式等。 约克工业冷冻机组部件 介绍-直接膨脹式經濟器 约克工业冷冻机组件 介绍-液位控制 约克工业冷冻机组件 介绍-液位控制阀 手动打开: 顺时针尽可能转动阀杆3,阀门就被强制打开。 ? 手动关闭: 逆时针转动阀杆3,直到阀被完全关闭。 约克工业冷冻机组件 介绍- PMFL液位调节主阀 约克工业冷冻机组件 介绍-吸气组合阀 约克工业冷冻机组件 介绍-回油器 每3个月开一次,运行8小时 发现油分中油位下将时启用回油器 昆腾控制中心介绍 昆腾控制中心分二个界面:运行状态、主菜单 按“HOME”可以进入运行状态 按“MENU”可以进入主菜单 运行状态页用于:开停机、加减载、查看运行数据 主菜单页用于:故障查看与复位、容量控制点调整、安全值修改、显示值校准、密码修改等 6 2 1 23 SLIDE OBJECTIVE Show the simplicity of the gas engine driven centrifugal chiller (same as vapor compression without the electric motor). SCRIPT Gas engine driven centrifugal chillers are simply the vapor compression cycle with a gas engine spinning the centrifugal compressor’s impeller. The impelled requires a specific revolutions per minute and horsepower in order for it to perform its function. 22 过热的好处与过冷的好处 压缩机有常用的RWBII、RWF、RXF等;H为高压级、B为低压级。 Perhaps the most important reason for using anti-friction bearings in a screw compressor is that they have less internal clearance than sleeve bearings. This allows tighter rotor to rotor positioning. Any gas compressed to high pressure in a screw will try to leak back to suction through any available leakage path. The most difficult leakage path to control is the path down the center directly between the two rotors. A 3 inch diameter journal bearing will require approximately 0.003 inch internal clearance in order to build an oil film. A cylindrical roller sized to handle the same load will have roughly half the internal clearance. With half the radial motion possible on each rotor this gives one quarter of the leakage path down the center and yields significantly better efficiency at

文档评论(0)

wyjy + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档