MSP430与12864连接驱动程序(KS0108)(国外英语资料).doc

MSP430与12864连接驱动程序(KS0108)(国外英语资料) #我nclude”MSP430x14x。h”/ /标准方程 #我nclude“math.h” #我nclude“stdlib.h” #我nclude“stdio . h” #我nclude“string.h” #我nclude“ctype.h” #我nclude“HZTable.h” #我nclude“ASCII816.h” #定义使用uint unsigned int #定义uchar unsigned char / / * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * #定义RS BIT0 #定义RW BIT1 #定义E BIT2 #定义CS1第3位 #定义CS2相加 #定义RST BIT5 #定义EL BIT6 / /背光 / /数据线:p4口,控制线:p5口 / / * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * uchar cradd1 cradd2; uchar item1[5]= { 0、1、2、3、50个};/ /欢迎使用 uchar第二条[5]= { 4、5、6、7,50个};/ /请等待…… / / = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = 空白short_delay(使用uint i) {使用uint j; (j = 0; =我;j + +); } 空白delayms(uchar tickms) { uchar计数,我; _NOP(); _NOP(); _NOP(); (我= tickms; 0;-) {(count = 0;数 = 58;计数+ +){;} _NOP(); } } / / * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 空白prl0(uchar com1)/ /写指令代码子程序(左) { P5DIR | = 0 x7f;/ / P5为输出口 P5OUT | = CS1;/ / csa = 1 P5OUT = ~ CS2;/ / csb = 0 P5OUT = ~ RS; P5OUT | = RW;/ / RS = 0,R / W = 1,以便读液晶状态 P4DIR = 0 x00;/ / P4口为输入口 做 { P5OUT | = E;/ / E = 1 cradd1 = P4IN; P5OUT = ~ E;/ / E = 0 } 在((cradd10x80)! = 0); P5OUT = ~ RW;/ / RW = 0 P4DIR = 0 xff;/ / P4口为输出口 P4OUT = com1; P5OUT | = E;/ / E = 1 P5OUT = ~ E;/ / E = 0 } / / * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 空白prl1(uchar dat1)/ /写显示数据子程序(左) { P5DIR | = 0 x7f;/ / P5为输出口 P5OUT | = CS1;/ / csa = 1 P5OUT = ~ CS2;/ / csb = 0 P5OUT = ~ RS; P5OUT | = RW;/ / RS = 0,R / W = 1,以便读液晶状态 P4DIR = 0 x00;/ / P4口为输入口 做 { P5OUT | = E;/ / E = 1 cradd1 = P4IN; P5OUT = ~ E;/ / E = 0 } 在((cradd10x80)! = 0); P5OUT | = RS;/ / RS = 1 P5OUT = ~ RW;/ / RW = 0 P4DIR = 0 xff;/ / P4口为输出口 P5DIR | = 0 x7f; / / the P5 is the export P5OUT = ~ CS1; / / csa = 0 P5OUT | = CS2; / / the CSB = 1 P5OUT = ~ RS; P5OU