原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
视频第4章 功率放大 5页(国外英文资料)
视频第4章 功率放大 5页(国外英文资料)
(1) explain the role of diode Dl and D2 in the circuit.
(2) what is the maximum undistorted output power of the circuit and the effective value of the required VO3?
(3) when the output signal of the T3 tube is VO3 = 10V, the output power, the tube consumption, the power and efficiency of the DC power supply are calculated.
Solution: (1) the diode D1 and D2 provide static bias voltage for the output triode to overcome the crossover distortion.
(2) according to the circuit:
The maximum output voltage of the circuit is undistorted:
The maximum output power of the circuit is undistorted:
Effective value of Vo3:
Example 4.6 OTL amplifier circuit as shown in Figure 4.4, set the characteristics of Tl and T2 symmetrical, VI sine voltage, VCC = 10V, RL=16, try to answer the following questions:
(1) what is the voltage at the end of the capacitor C2 when it is static? Which resistor can be adjusted to meet this requirement?
(2) when dynamic, if the output waveform appears cross over distortion, which resistor should be adjusted? How to adjust?
(3) if R1 = R3 = 1.2k, Tl and T2 are beta = 50, VBE = 0.7V, PCM = 200mW. What are the consequences of assuming any open circuit in Dl, D2, and R2?
Solution (1) static should be C2 = 1/2VCC = 5V, adjust the resistance value of R1 or R2 to meet this requirement.
(2) if there is a crossover distortion in dynamic condition, the resistance value of R2 should be increased until the crossover distortion is eliminated.
(3) if there is any open circuit in D1, D2 and R2, the quiescent current flowing through resistor R1 becomes the base current of T1 and T2, and the static power consumption of T1 and T2 is
PCM
Therefore, the burned power tube is burned.
Example 4.7. In the OTL amplification circuit shown in Fig. 4.5, known as VCC = VEE = 12V, RL = 8.
(1) select the parameters of the power tube, PCM, ICM and V (BR) CEO.
(2) for efficiency = 0.6 when the output power of PO.
Solution: (1) because of the maximum output power o
文档评论（0）