数字系统设计例子的.ppt

选做一到二题;数字钟实验;设计要求;设计提示;主控电路＊;;拔河游戏机;设计要求;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;设计提示;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;数字式竞赛抢答器;设计要求;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;设计提示; ;;洗衣机控制器;设计要求;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;设计提示;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;数字频率表;设计要求;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;设计提示;;设置1秒定时信号（周期为2秒），在1秒定时时间内的所有被测信号送计数器输入端。 计数器对CP1信号进行计数，在1秒定时结束后，将计数器结果送锁存器锁存，同时将计数器清零，为下一次采样测量做好准备。 ;设置量程档控制开关K，单位显示信号Y，当K=0时，为1?999Hz量程档，数码管显示的数值为被测信号频率值，Y显示绿色，即单位为Hz； 当K=1时，为1KHz?10KHz量程档，被测信号频率值为数码管显示的数值乘1000，Y显示红色，即单位为KHz。 ;设置超出量程档测量范围示警信号alert。计数器由四级十进制计数构成（带进位C）。若被测信号频率小于1KHz（K=0），则计数器只进行三级十进制计数，最大显示值为999.Hz，如果被测信号频率超过此范围，示警信号驱动灯光、扬声器报警；若被测信号为1KHz?10KHz（K=1），计数器进行四位十进制计数，取高三位显示，最大显示值为9.99KHz，如果被测信号频率超过此范围，报警。 ;左第一位;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;电子密码锁;设计要求;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;设计提示;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;脉冲按键电话按键显示器;设计要求;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;设计提示;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;乒乓球比赛游戏机;任务与要求;设计思路;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;交通信号灯控制器;任务与