电子套结机的维修（Maintenance of the electronic tacking machine）.docVIP

下载本文档

5
0
约3.45万字
约 10页
2017-07-15 发布于河南
举报
版权申诉

电子套结机的维修（Maintenance of the electronic tacking machine）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

电子套结机的维修（Maintenance of the electronic tacking machine）

电子套结机的维修（Maintenance of the electronic tacking machine） The fault characteristics and maintenance methods of these problems are frequently encountered in our daily work. The summary can be divided into four parts: the lifting foot mechanism, Feeding mechanism, tangent mechanism and optical coupling sensor. 1. Foot pressure mechanism: the more vulnerable part of this part is that the foot is not fit or lower down. The characteristic of this fault is that when stepping down The pedal, the foot is not in time to lower down, and the display of the fault is the e-6 - series. Before processing, understand the structure of the lifting part of the foot. FIG. 1 is the lifting press The schematic diagram of the structure, its motion flow is: solenoid (1) charging generates electromagnetic attraction armature (2) left shift, pull straight link (5), the support of connecting rod (5) makes sliding block (4) push downward pressure To lift the foot. From the structure, it is reasonable that the force of solenoid shall not be applied directly to the foot, but can effectively reduce the volume and energy consumption of the solenoid. but It is also difficult to design and process perfection in a series of links. Analysis of the above fault: when the control panel receives the instruction to put down the foot After that, disconnect the power of the solenoid and release the armature, so that the connecting rod is reset and the slider rises, and the pressure foot is lowered and the signal is given back to the control panel. If the control board is not in the control panel A successful release of the feedback signal will call the police. The reason that the pressure foot cannot be successfully lowered is that the neutral position of connecting rod (5) is not adjusted. When the connecting rod (5) is shown to the left by a Even after the solenoid release armature, the link (5) will be above the neutral position on the anti-dead point due to the reaction of the pressure of the foot. The pu