一级斜齿课程设计（Course design of grade one inclined tooth）.docVIP

下载本文档

0
0
约2.43万字
约 32页
2017-07-20 发布于河南
举报
版权申诉

一级斜齿课程设计（Course design of grade one inclined tooth）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

一级斜齿课程设计（Course design of grade one inclined tooth）

一级斜齿课程设计（Course design of grade one inclined tooth） I. transmission plan formulation The third data of the second group: the first stage cylindrical gear reducer in the design belt conveyor (1) working conditions: 10 years of life, 300 days per year, two shift work and stable load. (2) raw data: cylinder circumference force F = 1.7kn; Tape speed V = 1.4 m/s; Drum diameter D = 220mm. Kinematic sketch The choice of motor 1. Selection of motor type and structure type: according to the known work requirements and conditions, Y series three-phase asynchronous motor is chosen. 2. Determine the power of the motor: (1) total efficiency of transmission: Eta is always equal to eta 2 bearing x 2 bearing x - eta gear x - eta coupler = 0.96 * 0.992 * 0.97 * 0.97 * 0.992 = 0.86 (2) the working power required by the motor: Pd = FV/eta total 1000 1.4/1000 * 0.86 = 1700 x = 2.76 KW 3. Determine motor speed: Working speed of roller shaft: Nw = 60 x 1000 v/PI D = 60 * 1000 * 1.4 / PI by 220 = 121.5 r/min According to [2] are recommended in table 2.2 the reasonable range of transmission ratio, V belt transmission ratio = 2 ~ 4 Iv, single stage spur gear transmission ratio range Ic = 3 ~ 5, the reasonable range of the total transmission ratio I is I = 6 ~ 20, so the motor speed range of optional nd = I * nw = (6 ~ 20) * 121.5 = 729 ~ 2430 r/min The synchronous RPM for this range is 960 r/min and 1420r/min. It is found that there are three applicable motor models, as shown in table 8.1 The transmission ratio of the motor speed (r/min) transmission device of the scheme motor model rated power motor speed (r/min) KW is the same with the total transfer ratio belt gear 1 Y132s - 6, 3, 960, 7.9, 3, 2.63 2 y100l2-4 3 1500 1420 11.68 3 3.89 Incorporating the motor and actuator size, weight, price and ratio of belt drive, gear reducer, two schemes comparison: plan 1 for motor speed is low, gear size is larger, the price is higher. Plan 2 is moderate. Therefore, select the motor model y100l2-4. D