数字温度计液晶显示.docVIP

#includereg52.h #define uint unsigned int #define uchar unsigned char sbit mode=P1^0;//模式键 sbit add=P1^1;//加键 sbit dec=P1^2; //减键 sbit dq=P1^3;//18b20检测点 sbit dula=P1^4;//段选 sbit wela=P1^5;//位选 sbit buzzer=P2^1;//蜂鸣器 sbit rs=P2^4;//数据/命令选择端 sbit rw=P2^5;//读入/读出选择端 sbit en=P2^6;//使能端 bit sflag=0;//温度符号标志位 bit tflag=0;//温度检测时间到标志位 bit lflag=0; uchar code dcode[]={0x8e,0x60,0xee,0x9e,0x6e,0x9e,0x1c,0xce};//定义段码 uchar code wcode[]={0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,0xfe};//定义位码 uchar code str1[16]= temp: . C ;//定义字符串 uchar code str2[]= 05-05 00:00:00 ;//定义字符串 uchar tcount0,tcount1,scount=0; uint mou,day,hor,min,sec;//定义时分秒 void delay(uchar z)//延时子程序 { int i,j; for(i=z;i0;i--) for(j=110;j0;j--); } void delay_18b20(uchar t)//18b20延时子程序 { while(--t); } void write_com(uchar com)//写地址子程序 { rs=0; rw=0; en=1; P0=com; delay(1); en=0; } void write_dat(uchar dat)//写数据子程序 { rs=1; rw=0; en=1; P0=dat; delay(1); en=0; } void write_hms(uchar dat,uchar add)//时间数据处理子程序 { uint h,l; h=dat/10; l=dat%10; write_com(0x80+0x40+add); write_dat(h+0x30); write_dat(l+0x30); } void keycan()//键盘扫描函数 { if(mode==0)//模式键 { delay(5); if(mode==0) { scount++; if(scount=6) { scount=0; } switch(scount) { case 0: write_com(0x0c);TR0=1;break; case 1: TR0=0;write_com(0x0e);write_com(0xc0+0x0e);break; case 2: write_com(0xc0+0x0b);break; case 3: write_com(0xc0+0x08);break; case 4: write_com(0xc0+0x05);break; case 5: write_com(0xc0+0x02);break; } } while(mode==0);//松手检测 do { delay(5); } while(mode==0); } } void cfa_hms()//时间加进位处理子程序add { if(sec=60) { sec=0; min++; if(min=60) { min=0; hor++; if(hor=24) { hor=0; day++; if(day==31) { day=1; mou++; if(mou==13) { mou=1; } write_hms(mou,1); } write_hms(day,4); } write_hms(hor,7); } write_hms(min,0x0a); } write_hms(sec,0x0d); } void cfd_hms()//时间减进位处理子程