hybrid端口在二层交换机上的用法（The use of hybrid port on the second layer switch）.docVIP

下载本文档

26
0
约 7页
2017-07-22 发布于河南
举报
版权申诉

hybrid端口在二层交换机上的用法（The use of hybrid port on the second layer switch）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

hybrid端口在二层交换机上的用法（The use of hybrid port on the second layer switch）

hybrid端口在二层交换机上的用法（The use of hybrid port on the second layer switch） 1, port trunk applications Configure the environment parameter The 1.PC1 address of IP is 10.1.1.1/24, the IP address of PC2 is 10.1.1.2/24, the IP address of PC3 is 10.1.1.3/24, and the IP address of PC4 is 10.1.1.4/24; 2.PC1 and PC2 are respectively connected to the ports E0/1 and E0/2 of the switch SwitchA, and the ports belong to VLAN10 and 20; the PC3 and the PC4 are respectively connected with the ports of the switch SwitchB, the E0/10 and the E0/20, and the ports belong to VLAN10 and 20 respectively. 3.SwitchA connects to port SwitchB of port G1/1 through port G2/1; port G1/1 of SwitchA port and port of SwitchB is Trunk port, and allows VLAN10 and VLAN20 to pass through G2/1 port. Networking requirements 1.SwitchA and SwitchB are the same, VLAN PC can exchange visits. 2.SwitchA and SwitchB are different, and VLAN PC is forbidden to exchange visits. Switch Trunk port configuration flow Use the port configuration for the Trunk port to complete the transmission of VLAN in different between the switches, to PC machine belonging to the same VLAN, two cross layer access switch; or PC different VLAN cross switch three layer access to. Configuration process [SwitchA related configuration] 1. create (enter) VLAN10 and add E0/1 to VLAN10 [SwitchA]vlan 10 [SwitchA-vlan10]port Ethernet 0/1 2. create (enter) VLAN20 and add E0/2 to VLAN20 [SwitchA]vlan 20 [SwitchA-vlan20]port Ethernet 0/2 3. configure port G2/1 as Trunk port and allow VLAN10 and VLAN20 to pass [SwitchA]interface GigabitEthernet 1/1 [SwitchA-GigabitEthernet1/1]port link-type trunk [SwitchA-GigabitEthernet1/1]port trunk permit VLAN 1020 [SwitchB related configuration] 1. create (enter) VLAN10 and add E0/10 to VLAN10 [SwitchA]vlan 10 [SwitchA-vlan10]port Ethernet 0/10 2. create (enter) VLAN20 and add E0/20 to VLAN20 [SwitchA]vlan 20 [SwitchA-vlan20]port Ethernet 0/20 3. configure port G2/1 as Trunk port and allow VLAN10 and VLAN20 to pass [