小区重选参数c1、c2（Cell reselection parameters C1, C2）.docVIP

下载本文档

26
0
约7.26千字
约 8页
2017-07-23 发布于河南
举报
版权申诉

小区重选参数c1、c2（Cell reselection parameters C1, C2）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

小区重选参数c1、c2（Cell reselection parameters C1, C2）

小区重选参数c1、c2（Cell reselection parameters C1, C2） Cell selection criteria: 1, the chosen entry must belong to the chosen network 2, the district cell_bar_access_switch=YES 3, the districts C10 4, the districts priority level (CBQ) The parameter C1 is the judgment mark when the cell is selected: C1 = (received_signal_level-ACCMIN) -max (CCHPWR-P, 0) Max (CCHPWR-P, 0) =CCHPWR-P, if CCHPWR-P0 Max (CCHPWR-P, 0) =0, if CCHPWR-P0 C2 = C1CROTO*H (PT-T); PT is not equal to 31 C1CRO = C2; PT = 31 MS performs cell reselection 1, the district became BAR 2, in the maximum retransmission MAXRET settings, MS still failed to access the system 3, downlink on BERhigh, link fault occurs. 4, servingcell C10, continuous more than 5S. 5, NCELL of C1 greater than servingcell of C1 more than 5S time 6, another location area area of C2 is larger than the current district (C2CRH) time more than 5S. C2 is an optional parameter for GSMPHASE2, used only for cell reselection, and if C2 is not broadcast, use C1 as reselection parameter. C2=C1+ reselection compensation parameter + temporary compensation parameter *H (penalty time - measured time) Reselection compensation parameter: CELL_RESELECT_OFFSET (CRO) broadcast by system Temporary compensation parameter: TEMPORARY_OFFSET broadcast by system Penalty time: PENALTY_TIME broadcast by system Measured time: TMS measures the maximum time for a candidate cell level value of TOPSIXCELL If the penalty time measured time is 0, then H=1 If the penalty time measured time is 0, then H=0 If PENALTY=31, then C2=C1-CRO Similarly, the cell reselection of the same LAC, as long as the target C2 is the original C2, requires the lag factor after the cell reselection of different LAC. The reason for using C2: C2 has two more factors than C1, CRO and TO*H CRO: the use of CRO can artificially compensate for the optional nature of a cell. For example, in a signal quality is good, the user is relatively small cell, you can set its CRO larger, so that MS as much as pos