凸轮轴位置传感器的检测的方法（Method for detecting camshaft position sensor）.docVIP

下载本文档

3
0
约7.65千字
约 5页
2017-07-23 发布于河南
举报
版权申诉

凸轮轴位置传感器的检测的方法（Method for detecting camshaft position sensor）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

凸轮轴位置传感器的检测的方法（Method for detecting camshaft position sensor）

凸轮轴位置传感器的检测的方法（Method for detecting camshaft position sensor） A persons 2010-01-04 16:38 GT, GTX Holzer, Jetta camshaft position sensor on Santana 2000GSi using the engine mounted at one end of the intake cam, as shown in Figure 1, its structure as shown in figure 2. It is mainly composed of Holzer sensor and signal rotor. The signal rotor, or impeller, is mounted on the intake cam and fixed with bolts and seat rings. The partition board of the rotor is also called the blade, and there is a window on the partition board. The signal produced by the window is a low level signal, and the signal generated by the partition board is a high level signal. The Holzer sensor mainly consists of an integrated circuit, a permanent magnet and a guide diskette. The gap between the Holzer element and the permanent magnet is 1mm, and when the rotor of the signal rotates along with the intake camshaft, the partition plate and the window rotate from the gap between the integrated circuit and the permanent magnet. When the signal of the rotor separator into the gap, Holzer in IC field is bypassed, Holzer element no magnetic field lines through zero voltage UH, Holzer, integrated circuit output transistor cut-off, the sensor output signal voltage for high potential, about 4.0V; when the signal separator rotor leave a gap, the magnetic flux of the permanent magnet the magnetic element and Holzer integrated circuit to form a loop, then the Holzer voltage is about 2.0V, the integrated circuit output transistor turn-on, the sensor output signal voltage is 0.1V, low potential. When the engine is working, the signals generated by the crankshaft position sensor and camshaft position sensor are continuously input to the ECU. When the low potential ECU signal received at the same time a large lack of corresponding crankshaft position sensor (15 degrees) and low potential signal and camshaft position sensor corresponding to the window, we can identify 1 cylinder piston and ending on the compressi