- 14
- 0
- 约1.05万字
- 约 8页
- 2017-08-04 发布于河南
- 举报
串口并口PCI 接口总结(Serial interface and PCI interface summary)
A serial port
Serial ports are called serial interfaces, and computers now have two serial ports: COM1 and COM2. You can see the 9 pin D interface at the back of the computer, and sometimes we call it rs-232. There are many mobile phone data lines or logistics receivers that use COM to connect with computers.
Universal Serial Bus (Universal Serial Bus) referred to as USB, is the more widely the interface specification of computer application, the USB interface is one of the computer motherboard four pin interface, among which two needle to transmit data, on both sides of two needle for peripheral power supply. The USB interface is fast, easy to connect, does not require external power supply, and has a good compatibility with the outside world, which can connect up to 127 peripherals. USB has two specifications, USB1.1 and USB2.0.
USB interface can connect speaker, Modem (Modem), digital cameras, monitors, joystick, scanner, mouse, keyboard and other peripheral equipment, make these peripherals can be hot plug, is not off plug the USB device.
Interface type:
RJ - 45 interface is the most commonly used Ethernet interface, RJ45 is a common name, refers to the standardization of IEC 603-7 (60), using the connectors by international standard definition of eight (8) needle position modular jack or plug.
The rs-232 interface (also known as EIA rs-232-c) is the most commonly used serial communication interface. It was established in 1970 by the United States electronic industry association (EIA) united bell system, modem manufacturers and computer terminal manufacturers to develop the standard for serial communication. Its full name is the data terminal equipment (DTE) and data communications equipment (DCE) between the serial binary data exchange interface technology standard the standard adopts a DB25 connector of 25 feet, the content of the signal for each pin connector is regulated, also is regulated to a variety
您可能关注的文档
- 南开11春学期《资产评估》在线作业(The online homework of asset appraisal in the spring semester of nankai).doc
- 南开11秋学期《高级管理会计》在线作业(In the 11th autumn semester, senior management accounting is online).doc
- 南开12秋学期《成本与管理会计》在线作业(Work on cost and management accounting in the 12th autumn semester).doc
- 南开13春学期《财务分析概论》在线作业(An introduction to financial analysis in the spring semester).doc
- 南开13秋学期《高级成本会计》在线作业(South open 13 autumn semester advanced cost accountant online homework).doc
- 南开15秋学期《审计学》在线作业满分(A full mark of the online work of audit in the 15th autumn semester of nankai university).doc
- 南开大学 13春学期《工程施工》在线作业(Nankai university 13 spring semester project construction online homework).doc
- 南开10秋学期《管理经济学(一)》在线作业(An online assignment of management economics (1) in the autumn semester of nankai).doc
- 南开大学13秋学期《人力资源开发》在线作业(Human resources development online homework of nankai university).doc
- 南开大学2013春学期《管理经济学(一)》在线作业(Nankai university (2013) management economics (1) online homework).doc
- 中国国家标准 GB/Z 37551.300-2026海洋能 波浪能、潮流能及其他水流能转换装置 第300部分:河流能转换装置发电性能评估.pdf
- GB/T 44937.3-2025集成电路 电磁发射测量 第3部分:辐射发射测量 表面扫描法.pdf
- 中国国家标准 GB/T 44937.3-2025集成电路 电磁发射测量 第3部分:辐射发射测量 表面扫描法.pdf
- 《GB/T 44937.3-2025集成电路 电磁发射测量 第3部分:辐射发射测量 表面扫描法》.pdf
- 中国国家标准 GB/T 44937.1-2025集成电路 电磁发射测量 第1部分:通用条件和定义.pdf
- GB/T 44937.1-2025集成电路 电磁发射测量 第1部分:通用条件和定义.pdf
- 《GB/T 44937.1-2025集成电路 电磁发射测量 第1部分:通用条件和定义》.pdf
- 中国国家标准 GB/T 4937.37-2025半导体器件 机械和气候试验方法 第37部分:采用加速度计的板级跌落试验方法.pdf
- 《GB/T 4937.10-2025半导体器件 机械和气候试验方法 第10部分:机械冲击 器件和组件》.pdf
- 中国国家标准 GB/T 44937.2-2025集成电路 电磁发射测量 第2部分:辐射发射测量TEM小室和宽带TEM小室法.pdf
原创力文档

文档评论(0)