波峰焊常见的小问题及维修（Common minor problems and maintenance of wave soldering）.docVIP

下载本文档

2
0
约7.42千字
约 8页
2017-08-04 发布于河南
举报
版权申诉

波峰焊常见的小问题及维修（Common minor problems and maintenance of wave soldering）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

波峰焊常见的小问题及维修（Common minor problems and maintenance of wave soldering） Why does the welding of wave solder weld even? 1. The preheating temperature of the flux is too high or too low, generally at 100 ~ 110 degrees, too low, and the flux is not high. Too high the flux will paste. 2. Check the tin stove temperature, control at 265 degrees or so, had better use temperature meter to measure the wave peak temperature when playing, because the temperature sensor of the equipment can be in the bottom of the furnace or other location. 3. Regularly check the analysis of tin components. It is possible that copper or other metals contain excessive amounts, resulting in reduced liquidity of tin and easy to cause tin. 4. Check the orbital Angle of wave soldering, 7 degrees is the best, and taiping is easy to hang tin. Clean the tin stove every day, and even tin can cause tin. Welcome to my taobao shop love pat boring 2011 specializing in wave soldering accessories 2. What is the reason for the flux leakage of the 2 wave solder nozzle If after the nozzle is done, the thimble does not have a timely return to the reposition, there will be a water column of the same flux to flow out. If you are close to pre-heating, there will be safety hazards. The reason is: inside the nozzle, the rubber ring at the thimble area is relatively large with the friction inside, causing the thimble to return slowly under the action of the spring! Butter on the top of the rubber band. Welcome to my taobao shop love pat boring 2011 specializing in wave soldering accessories 3. How do you solve the hole in the welding of wave soldering Wave soldering occurs in the weld hole, cavity is also called hole, because tin is not filled with PCB plug hole cause. The general reasons are: 1. Maladjustment of component foot and pore size (majority design problem) 2. When PCB hole is processed, it deviates from the center of the welding disk 3. The welding disc is incomplete 4. Oxidation or burr around the hole 5. Oxi