架空线路中导线架设施工工艺（Construction technology of wire erection in overhead line）.docVIP

下载本文档

8
0
约1.39万字
约 15页
2017-08-04 发布于河南
举报
版权申诉

架空线路中导线架设施工工艺（Construction technology of wire erection in overhead line）.doc

1、本文档共15页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

架空线路中导线架设施工工艺（Construction technology of wire erection in overhead line） The construction technology of erecting wire overhead line The range of 1 This technology is applicable to wire 10kV and below the overhead distribution lines erection engineering. 2 construction preparation 2.1 material requirements: 2.1.1 the equipment and materials shall be prescribed with the current standard contract home, and should have product certification. 2.1.2 wire: 2.1.2.1 wire should not loose strands, cross, folding, fracture and damage, bare aluminum wire should not have serious corrosion phenomenon. 2.1.2.2 should not have serious corrosion phenomenon. 2.1.2.3 insulated wire surface should be flat, smooth, uniform color, the thickness of the insulating layer should meet the requirements. The insulation layer shall be extruded tightly, and easy to peel, insulated wire ends should be sealed. 2.1.2.4 wire should be consistent with the numerical minimum section shown in table 3-76. The minimum wire section (mm2) table 3-76 Wire type 10kV Non residential areas residential area below 1kV Aluminum conductor ACSR Copper wire 35 Twenty-five 1625 From 16 to 25 From 1616 to 25 From 16 to 25 The diameter is 3.2 ~ 4.0mm 2.1.3 Znsulator, butterfly insulator 2.1.3.1 porcelain and iron, and no combination of skew phenomenon closely, galvanized iron good. 2.1.3.2 enamel smooth, no cracks, spots, missing glaze, burn, burn or enamel defects such as bubbles. The suitable 2.1.3.3 elastic pad, spring pin. AC voltage test results of 2.1.3.4 high voltage insulator must comply with the requirements of construction specification. 2.1.4 tie line: line tied bare wire should be used with the same metal wire single strands, the diameter should not be less than 2.0mm, should be made of insulating tie wire insulated wire. 2.1.5 strainclamp, parallel groove clamp, clamp pipe, aluminum strip 2.1.5.1 surface should be smooth, no cracks, burrs, fins, blisters, bubbles and other defects. 2.1.5.2 clamp flexible rot