- 1、本文档共15页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
Drive Pulley Lagging the importance of proper (驱动皮带轮落后正确的重要性)
Drive Pulley Lagging – The Importance of Proper Technical Analysis
and Selection
Presented at the 2010 Annual SME Meeting in Phoenix, AZ
Paul Ormsbee, Allen V. Reicks P.E.
Overland Conveyor Company, Inc. Lakewood, CO
ABSTRACT
A follow-up paper to “Ceramic Lagging – A Good Thing Can Be Costly if Misused” presented at
the 2006 annual meeting. The performance of drive pulley lagging has become much more
important in recent years due to higher torque drives, higher conveyor belt speeds, and the use
of ceramic lagging. The popularity of ceramic lagging is due to the reduced risk of drive pulley
slip and reduction of lagging wear. However, the application of ceramic lagging to a pulley can
lead to lagging failure of costly wear to the belt; the most expensive component on the
conveyor. Modern analysis and simulation tools and a better understanding of how lagging and
belting interact during torque transmission are necessary for a modern conveyor designer to
select this relatively inexpensive but important component. Case studies will be presented as
well as analysis techniques.
INTRODUCTION
There are a few basic reasons for the application of lagging to both driven and non-driven
pulleys.
Lagging serves as a protective layer guarding the pulley from premature failure due to
abrasion.
While protecting the pulley, the lagging can also protect the conveyor belting from a
similar sort of wear failure caused by abrasion.
Lagging can also creates an increase in friction between the pulley and the belt which is
usually needed when there is a requirement for torque transfer through the pulley to the
belt.
Lagging is applied to nearly all conveyors to address at least one (if not all) of the basic points
above. In addition to performing the points listed above, lagging should be applied in a way that
the lagging its
您可能关注的文档
- Distribution Feeder Principles GE Grid Solutions(配电线路原理 通用电气的电网解决方案).pdf
- Distribution of Belt Anchorage Locations in the (带锚定位置的分布).pdf
- DIVISION 16 ELECTRICAL Northern Arizona (部门16 电气亚利桑那州北部).pdf
- DLM 2000M 2000 Yokogawa(2000 日本横河DLM 2000).pdf
- DIY Guide to Building your own Generator (建立你自己的发电机,DIY指南).pdf
- DMG – innovative technologies JOURNAL 02(DMG 创新技术02》杂志上).pdf
- Doctor of Ministry Degree Tennessee Temple (部博士学位田纳西州的寺庙).pdf
- DOCK SYSTEMS, LLC MARINEPRO MP(码头系统,LLC MARINEPRO MP).pdf
- Dogfish Shark Dissection University of Miami(角鲨鲨鱼解剖迈阿密大学).pdf
- Dotted Lined Handwriting printables Your (点缀着笔迹小册子你).pdf
文档评论(0)