外墙保温系统施工要点（Main points of construction of exterior wall insulation system）.docVIP

下载本文档

1
0
约7.07千字
约 6页
2017-08-15 发布于河南
举报
版权申诉

外墙保温系统施工要点（Main points of construction of exterior wall insulation system）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

外墙保温系统施工要点（Main points of construction of exterior wall insulation system）

外墙保温系统施工要点（Main points of construction of exterior wall insulation system） Main points of construction of exterior wall insulation system 1.1 base wall should be solid walls should be smooth, clean, clean the dust, oil, release agent, paint, hollowing and weathering etc. affect the bond strength of debris. 1.2, with 2 meters by foot inspection wall roughness, the maximum deviation is greater than 4mm, the use of 1:3 cement mortar leveling. 1.3, if the grass-roots wall does not have bonding conditions, the method of fixing with the fixed parts can be adopted directly. The number of the fixed parts shall be determined according to the height of the building and the nature of the wall. 2. bullet line In accordance with the provisions of the drawings play water level in the design of expansion joints at the telescopic seam width pop-up wall line etc.. A vertical line is arranged at the position of the Yin and Yang angles, and vertical lines are ejected on the two wall surfaces, and the verticality of the heat insulation plate is checked by the line. 3. polymer cement paste Use a clean plastic bucket, pour 5.5kg of the water, add 25kg polymer glue, and use a low speed mixer, stir into a moderate consistency of the mortar, set aside 5 minutes. Stir again before use. Well adjusted mortar should be used up in 2 hours. 4.. Laying over the net Cut over packet mesh width as the total thickness of the insulation boards 200mm+. First, on the grass-roots wall, all doors, windows, holes, perimeter and system terminals, coated adhesive polymer mortar, the width of 100mm, thickness of 2mm. The net cloth is cut to prevent the 100mm from being stored in the mortar, and the mesh is not allowed to be exposed. The excess polymer glue on the edge is scraped off, and the net cloth of the part thrown off is kept clean. 5. laying insulation board 5.1 if the insulation board for the Extrusion board, it should be painted on the side of the adhesive mortar besmear a dedicated interface agent, p