旋喷桩施工工艺（Jet grouting pile construction process）.docVIP

下载本文档

7
0
约2.74万字
约 25页
2017-08-17 发布于河南
举报
版权申诉

旋喷桩施工工艺（Jet grouting pile construction process）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

旋喷桩施工工艺（Jet grouting pile construction process）

旋喷桩施工工艺（Jet grouting pile construction process） Ask: how high pressure jet grouting pile construction? Process and others? Http:///forum/detail547732_1.html youre here. Theres a lot of information about that High pressure jet grouting technology Material selection and preparation Jet grouting is impact by high-pressure liquid flow and destruction of soil and soil mixed into a new solid jet, according to process requirements, should have the following characteristics: slurry grouting fluid has good sprayability; sufficient stability; slurry gas should be less; the gelation time of the slurry can mediate excellent mechanical properties; good; non-toxic, odorless, high seed setting rate. Water cement ratio generally adopts 1:1~1.5:1 cement grout. Prepare adequate cement grout according to the construction requirements before spraying, Two. Determination of swirl injection parameters 1. Determination of pressure parameters Under normal circumstances, increase the pump pressure to increase its flow and flow rate, thereby increasing the injection force. Based on past experience, the project selection pressure: 0~3 meters, by 25Mpa, 3 meters below the 23 Mpa. 2. Determination of rotational lifting parameters The speed of rotation and lifting is related to the radius of jet, and the effective radius is related to the geometry and injection angle of nozzle, and directly affects the characteristics of jet. According to the construction experience, the injection speed should be controlled within the range of 25~28cm/min, and the rotation speed should be controlled within the range of 20~28r/min. Among them, the top 1m should choose a slower speed and lifting speed. Generally 20~23cm/min, speed up, 20r/min rotation. 3 nozzle diameter The nozzle installed on the side of the drill is the key part of the jet grouting. The size of the powder injection has a great influence on the jet flow velocity. In general single pipe grouting, the nozzle diameter is chosen 2.0~3.2mm. Three, det