电工电缆功率耗电量计算公式大全（Calculation formula for power consumption of electrical cables）.docVIP

下载本文档

26
0
约7.85千字
约 8页
2017-08-18 发布于河南
举报
版权申诉

电工电缆功率耗电量计算公式大全（Calculation formula for power consumption of electrical cables）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

电工电缆功率耗电量计算公式大全（Calculation formula for power consumption of electrical cables）

电工电缆功率耗电量计算公式大全（Calculation formula for power consumption of electrical cables） Formula Daquan electrical cable | | | power consumption The calculation formula of electric power The calculation formula of electric power, voltage multiplied by the current, this formula is defined, the power is always right, applicable to any situation. For a pure resistance circuit, such as resistance, light bulbs, can use the current multiplied by the square resistance and the square of the voltage divided by the resistance formula, which is derived from Ohms law. But for the non pure resistance circuit, such as motors, can only use voltage multiplied by the current the formula for motor, Ohms law is not applicable, that is to say, the voltage and current is not proportional. This is because the motor in operation will have a counter electromotive force. For example, the external voltage is 8 volts, 2 ohm resistor, the back EMF is 6 volts, the current is (8 - 6) /2 = 1 (an), instead of 4. So the power is 8 x 1 = 8 (w). In other words Joule, is the formula of resistance heating, the heating power is multiplied by the square of the current resistance , which is always right. Also take the above example, the power of motor heating is 1 x 1 x 2 = 2 (W), that is to say, the total motor power of 8 watts, the heating power is 2 watts, 6 watts for the rest of the mechanical work. The calculation formula of cable 1.: squeeze before the sheath thickness diameter x 0.035+1 (with the power cable, the nominal thickness of single core cables shall be not less than 1.4mm, the nominal thickness of multi core cable should not less than 1.8mm) 2. on-line measurement of sheath thickness: sheath thickness (= perimeter extrusion sheath after squeezing the sheath circumference) /2 pi Or = sheath thickness (perimeter - extrusion sheath after squeezing the sheath circumference * 0.1592) The 3. insulation thickness of the thinnest point: nominal value x 90%-0.1 4. single core sheath thinnest point: nominal