PIC18F45K22双串口实验.docxVIP

PIC18F45K22双串口实验查询方式（16MHz）/*串口1、2收发，收到数据原样发送出去*/#include p18cxxx.h//#pragmaconfig FOSC=HSMP,PLLCFG=ON,PRICLKEN = OFF,FCMEN = OFF,IESO = OFF,PWRTEN = ON,BOREN = SBORDIS,WDTEN = OFF,MCLRE = EXTMCLR#define uchar unsigned char#define uint unsigned intvoid main(void){ ANSELC=0; TRISC=0xff; ANSELD=0; TRISD=0xff; RCSTA1bits.SPEN = 1;/*使能串口（将RX和TX引脚配置为串口引脚）*/TXSTA1bits.SYNC = 0;/*异步模式*/SPBRG1 =64*(1*3+1)/9600-1;/*波特率寄存器置值，设置波特率*/TXSTA1bits.BRGH = 1;/*速度模式：高速*/RCSTA1bits.CREN = 1;/*接收使能*/TXSTA1bits.TXEN = 1;/*发送使能*/TRISD=0xC0;RCSTA2bits.SPEN = 1;/*使能串口（将RX和TX引脚配置为串口引脚）*/TXSTA2bits.SYNC = 0;/*异步模式*/SPBRG2 =64*(1*3+1)/9600-1;/*波特率寄存器置值，设置波特率*/TXSTA2bits.BRGH = 1;/*速度模式：高速*/RCSTA2bits.CREN = 1;/*接收使能*/TXSTA2bits.TXEN = 1;/*发送使能*/while(1){if (PIR1bits.RC1IF==1){TXREG1=RCREG1;}if (PIR3bits.RC2IF==1){TXREG2=RCREG2;}}}二、中断方式（16MHz）/*串口1、2收发，收到数据原样发送出去*/#include p18cxxx.h//#pragmaconfig FOSC=HSMP,PLLCFG=ON,PRICLKEN = OFF,FCMEN = OFF,IESO = OFF,PWRTEN = ON,BOREN = SBORDIS,WDTEN = OFF,MCLRE = EXTMCLR#define uchar unsigned char#define uint unsigned intuchar DSY_CODE[]={0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0xff};ucharwei[]={0x80,0x40,0x20,0x10,0x08,0x04,0x02,0x01};void PIC18F_High_isr(void);/*中断服务函数声明*/void PIC18F_Low_isr(void);#pragma code high_vector_section=0x8void high_vector (void){_asmgoto PIC18F_High_isr _endasm}#pragma code low_vector_section=0x18void low_vector (void){_asmgoto PIC18F_Low_isr _endasm}#pragma code#pragma interrupt PIC18F_High_isrvoid PIC18F_High_isr (void){if(PIR1bits.RC1IF==1){TXREG1=RCREG1;}}#pragmainterruptlow PIC18F_Low_isrvoid PIC18F_Low_isr (void){if (PIR3bits.RC2IF==1){TXREG2=RCREG2;}}void DelayMS(uint x) //延时函数{ unsigned inti; for(;x0;x--) for(i=190;i;i--);}void main(void){ ANSELC=0; TRISC=0xff; ANSELD=0; TRISD=0xff; RCSTA1bits.SPEN = 1;/*使能串口（将RX和TX引脚配置为串口引脚）*/TXSTA1bits.SYNC = 0;/*异步模式*/SPBRG1 =64*(1*3+1)/9600-1;/*波特率寄存器置值，设置波特率*/TXSTA1bits.BRGH = 1;/*速度模式：