实战八、红外线遥控器读码机（Actual combat eight, infrared remote control code reader）.doc

下载文档 降价啦

8
0
约1.28万字
约 29页
2017-08-20 发布于河南
举报
版权申诉
保障服务

实战八、红外线遥控器读码机（Actual combat eight, infrared remote control code reader）.doc

1、本文档共29页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

实战八、红外线遥控器读码机（Actual combat eight, infrared remote control code reader）

实战八、红外线遥控器读码机（Actual combat eight, infrared remote control code reader） Infrared remote control code reader, with this example, with the station kit, you can read any 6121 or 6122 (CD6121/CD6122/SC6121/SC6122) and its compatible chip infrared remote control user code, key code. This example is an infrared remote control receiver decoding program, the program digital tube display, using the timer interrupt method of dynamic scanning Dynamic display of two digital tube method, interrupt method, we interrupt to 3MS, so as to exchange two digital tube turns lighting. When the infrared receiving head is aligned with the test board, the button to be measured is pressed lightly according to the measured button of the remote controller. At this time, the two digital tube in the experiment board will display the key code of the key, (shown as 16 hexadecimal), touch the S10 of the experimental board, the display is switched to show the current remote control user code 8 low, touch the S11 of the experimental board, at this time the display switch to show the current remote control user code 8 high, Touching the S9 of the experimental board at this time shows again the key code that shows the current key Note: all displays are 16 hexadecimal,AisA,Bisb,Cisc,Disd,EisE, andFisF. Note; remote control 6121 launch codes as follows: synchronization (boot code) +32 (user data code code low 8 + 8 + user code + key key code code) The boot code is made up of the high level plus 4.5MS of the 9MS, and we receive the high level of 9MS plus the 4.5MS that is just inverting to zero The data code0is made up of the high level plus 560US of the 560US and the low level plus 560US of the inverting 560US when it is received The data code1is made up of the high level of the 560US plus 1.69MS, and the high level of the low level plus 1.69MS of the 560US when it is received The program file name: MCD-RMT.ASM *******************************************************************; RTCC EQU 01H; defines the