蒂森mc2出(--)后的简单解决方法（Thyssen MC2 out (-) after the simple solution）.docVIP

下载本文档

8
0
约6.66千字
约 7页
2017-08-20 发布于河南
举报
版权申诉

蒂森mc2出(--)后的简单解决方法（Thyssen MC2 out (-) after the simple solution）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

蒂森mc2出(--)后的简单解决方法（Thyssen MC2 out (-) after the simple solution）

蒂森mc2出(--)后的简单解决方法（Thyssen MC2 out (-) after the simple solution） Thyssen MC2 (-) simple solution after the There are a variety of reasons N, I can only briefly say my own views ~ if there is a wrong place, also hope to master a lot of pointing out! ThyssenKrupp Elevator (-) there are generally self protection function of the elevator itself, is generally the elevator maintenance is not in place due to emergence of adjustment (-). If you have a diagnosis, youd better look at 0100 of the fault codes first, so that it is easy to analyze and solve the problem, If there is no diagnosis, you can try the following method: Generally after (-) after the power failure can be restored, but this can not solve the problem completely. If the power supply fails to solve the problem, it should be checked as follows. That also can repair after the parallel operation?? It is also in the flat area If the first thing to consider all relevant leveling to brake door zone switch to ZS switch ~ ~ ~ contactor emergency stop loop hall car door lock and so on to should be in the flat floor area! If you can go to overhaul, the general problem in advance to open the door in this respect ~! Check the top of the car: ZS switches and related lines! And contactor and relay contact check! If you dont want to use the function of opening the door ahead of time, you can cancel the function of opening the door in advance. If you can not go, inspection should generally check: 1, the brake detection switch to Should be adjusted to the right place. If the check switch is in place, the probability of going out will be much smaller! Adjustment method: the computer room overhaul, the S805 switch is pressed (that is, the MC2 board on the far right of the red button, press it, then check the switch on the switch In the invalid state) and then began to adjust the detection switch to optimum adjustment method: in the elevator stop state, take a piece of the old ID card inserted into the first round there to swit