夏普复印机特殊故障代码的复位方法（Method for resetting special fault code of SHARP copier）.docVIP

下载本文档

125
0
约2.51万字
约 36页
2017-08-30 发布于河南
举报
版权申诉

夏普复印机特殊故障代码的复位方法（Method for resetting special fault code of SHARP copier）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

夏普复印机特殊故障代码的复位方法（Method for resetting special fault code of SHARP copier）

夏普复印机特殊故障代码的复位方法（Method for resetting special fault code of SHARP copier） Method for resetting special fault code of SHARP copier Special fault code reset method of special fault code 700 / 800 SHARP SHARP copier series copiers are mainly HX (H1 H8, heat roller fixing device fault), Lx (L1-L6, micro switch / photoelectric switch fault, Ux (U1U2), low battery voltage or data transmission fault) and Pl (exposure lamp abnormal temperature fuse). The U1 instruction with 13 reset, other special instructions for fault code 14 reset. Special fault code SHARP 1000 / 2000 series copiers are mainly HX (H2-H4, heat roller fixing device fault) and U2 (memory read and write fault). Among them, U2 with instructions to 16 reduction and other special fault code 14 reset command. SHARP 7000 / 8000 Series copier special fault code, mainly HX (H3, H4, hot roller fuser fault) and U1 (battery voltage is low). The U1 is reset by the instruction 13, and the H3 H4 is reset by instruction 14. The sequence of the reset operation is shown in the figure In addition, a special fault code for SHARP Z60 copier with U (motherboard battery low), L (micro switch fault) and H (failure of hot roll fuser (F), fixing the lamp or temperature fuse) said, with 1 reset command. Reset, in order to press the clear key, duplicate keys, (addend key), (digital subtraction key) key 1 and the copy button. Note: (1) the key should be pressed within 5 seconds: (2) SHARP, 750, 770, 771, 780, 781, 825 and other copiers press duplicate keys, other copiers press the pause button; (3) at this time all the display on the operating board disappears, the main motor stops rotating, and the copier is ready to receive instructions (when the main motor is rotated, the copier does not accept instructions); (4) SHARP 1000 / 2000 series 1016, including SHARP copier 1020, 1025, 1116, 2014, 2020, 2022, 2027, 2040, 2114, 2214 SHARP 7000/8000 series copiers copiers; including SHARP 7320, 7370, 7700, 7750, 7800, 7850, 8570 and 8870 cop