h型钢t型钢自动气割工艺守则（H type steel T steel automatic cutting process code）.docVIP

下载本文档

2
0
约7.51千字
约 7页
2017-09-01 发布于河南
举报
版权申诉

h型钢t型钢自动气割工艺守则（H type steel T steel automatic cutting process code）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

h型钢t型钢自动气割工艺守则（H type steel T steel automatic cutting process code）

h型钢t型钢自动气割工艺守则（H type steel T steel automatic cutting process code） Automatic cutting process steel H steel, T code Two, H steel, T steel automatic cutting process code 1. Preface 1.1 automatic flame straight cutting cutting technology is a high quality and high efficiency, it is The main characteristics of centralized gas supply, scale discharging, automatic cutting; 1.2. This code specifies the basic requirements of cutting work, and the work must comply with the basic norms. 2. automatic cutting technician 2.1 automatic cutting mechanic should first be a qualified technician must understand the basic knowledge of cutting, cutting, cutting the master basic skills. 2.2 automatic cutting mechanic to centralized gas supply system (bus) of the basic principle, piping layout, structure and principle of all kinds of body, safety norms have a basic understanding and mastering; 2.3 automatic cutting mechanic should also the structure and performance of cutting machine, the structure and principle of all kinds of body have a basic understanding and knowledge; The structure and principle of the 2.4 automatic cutting torch with the mechanic to fully understand. And maintain certain maintenance and repair skills; 2.5 automatic cutting mechanic should also fully grasp the cutting process parameters, and make correct judgment to various defects, take prompt measures to eliminate the skill. 2. preparation before cutting 3.1 check the material size determined by the material collector; 3.2 of the cutting process conditions are reviewed; (including environmental condition of process equipment, equipment etc.) The best position of 3.3 on the basis of marking and process specification adjustment cutting torch, the torch nozzle should be perpendicular to the surface of the plate, the verticality of not more than 4% of the thickness, and not more than 2mm; 4. working procedures and cutting parameter selection The 4.1 is determined according to the number of oxygen supply in the plate