- 1、本文档共4页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
粗糙度计算(Roughness calculation)
粗糙度计算(Roughness calculation)
The surface roughness is now attracted the attention of the industry, the forum also often asked about how to improve the surface roughness of the post. Today about the turning on surface roughness. The picture above is turning surface roughness calculation method of cutting parameters, only need to be calculated in the highest possible surface roughness (the following statement all with low roughness is fine, high roughness is thick)
Turning surface roughness = square *1000/ for each turn feed point R by 8
The above calculation is theoretically possible to achieve the most bad effect, in fact due to the quality of the tools, the rigidity of the machine tool precision, cutting fluid, cutting temperature, cutting speed, material hardness and other reasons, will increase or decrease the roughness, if you use the calculated calculation above the roughness can meet to achieve the effect of change of cutting parameters. But the feed is generally closely related to the cutting depth, the general feed is cut between the depth of 10%~20%, the effect of cutting is the best cutting depth, because the width and thickness of the chip is the most proportion
I explain in detail below a key parameters of the formula above about the effect of roughness, if there is not please advice:
1: feed - the greater the feed, the greater the roughness, the greater the feed, the higher the processing efficiency, the smaller the tool wear, so the feed is generally final, according to the required roughness of the final set of feed
2: tool point R - the greater the tool R, the lower the roughness, but the cutting force will continue to increase, rigid requirements of the machine tool higher, the higher the rigidity of the material itself. The following 6150 suggestions do not use more than R0.8 lathe tool cutting steel and aluminum alloy, do not use R0.4 above the tip, otherwise the car out of roundness, straightness tolerances and so on cant guarantee, even can redu
您可能关注的文档
- 离心式水泵的组成(Composition of centrifugal water pump).doc
- 离心泵原理及结构(Principle and structure of centrifugal pump).doc
- 离心泵对小儿体外循环血小板功能的影响(Effect of centrifugal pump on platelet function in children undergoing cardiopulmonary bypass).doc
- 离子交换色谱(Ion exchange chromatography).doc
- 福建省南安一中2011届高三上学期期中试题 生物(2011 middle school senior middle school in Fujian, Nanan).doc
- 离子吸收(植物)(Ion absorption (plant)).doc
- 离职员工索工管理资遭拒 青岛美育称未签约属义工(Employees working capital management Cable refused Qingdao called volunteers did not sign the aesthetic education).doc
- 离职前单位要管理求先填申请书(Before leaving the office, management should first fill in the application).doc
- 禽包涵体肝炎(Avian inclusion body hepatitis).doc
- 禽病诊断技巧及原粉用药指南(Poultry disease diagnosis techniques and powder medication guide).doc
- 2023年08月湖北老河口市第一医院招考聘用43人笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 2023年08月浙江杭州市萧山区第一次机关事业单位招考聘用编外人员76人笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 2023年08月甘肃陇南市两当县招考聘用专职社区工作人员10人笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 2023年08月重庆市渝北区大湾镇公开招录7名村综合服务专干笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 2023年08月湖北应城市事业单位专项招考聘用驻军单位现役军官随军家属笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 2023年08月甘肃省临洮县招考33名专职社区工作者笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 2023年08月重庆市忠县卫生健康事业单位面向农村订单定向医学生公开招聘8人笔试上岸试题历年高频考点难、易错点摘选附带答案详解.docx
- 科技感物联网PPT大纲.pptx
- 商务助理的年终总结.pptx
- 有关包虫病的PPT大纲.pptx
文档评论(0)