cisco路由器基本配置命令（Cisco router basic configuration command）.docVIP

下载本文档

0
0
约9.35千字
约 17页
2017-09-05 发布于河南
举报
版权申诉

cisco路由器基本配置命令（Cisco router basic configuration command）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

cisco路由器基本配置命令（Cisco router basic configuration command）

cisco路由器基本配置命令（Cisco router basic configuration command） EN to enter the privileged mode Conf configuration mode In S0 into serial 0 port configuration IP add xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx add IP address and mask, telecommunications distribution Enca hdlc/ppp or PPP HDLC binding link protocol IP unn E0 Exit back to the global configuration mode. In E0 into the Ethernet interface configuration IP add xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx add IP address and mask, telecommunications distribution Exit back to the global configuration mode. IP route S 0 to add the routing table ENA password password Write Exit According to the above China Telecom DDN line most application Ordinary user mode Enable into a privileged user mode Exit exit configuration The help help system Language mode switch Ping check the network connection and the host host is reachable Show display system information Telnet remote login function Tracert tracking to the destination after the router privileged EXEC #? The removal of clear statistics Clock management system clock Configure configuration mode Debug open the debug switch Disable return to the normal user mode Download download the new version of the software and the configuration file Erase the configuration in the FLASH erase Exec-timeout open the EXEC timeout exit switch Exit exit configuration Set or clear the initial configuration to mark first-config The help help system Language mode switch Monitor open the user screen debugging information output switch No turn off debugging switch Ping check the network connection and the host host is reachable Restart the reboot router Setup router configuration parameters Show display system information Telnet remote login function Tracert tracking to the destination after the router Unmonitor close user screen debugging information output switch Write the current configuration parameters saved to FLASH MEM Global configuration mode The aaa-enable can configure AAA (authentication, authorization and