lvds信号pcb布线技巧（PCB routing skills for LVDS signals）.docVIP

下载本文档

38
0
约6.36千字
约 5页
2017-09-05 发布于河南
举报
版权申诉

lvds信号pcb布线技巧（PCB routing skills for LVDS signals）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

lvds信号pcb布线技巧（PCB routing skills for LVDS signals）

lvds信号pcb布线技巧（PCB routing skills for LVDS signals） LVDS PCB signal wiring technique A printed circuit board of LVDS signal generally cloth into multilayer board. Because the LVDS signal belongs to the high speed signal, the adjacent layer should be formation of the LVDS signal shielding to prevent interference. The density is not a big board, allowing the physical space conditions, the best LVDS signal and other signals respectively in different layers. For example, for four layer, can usually be carried out according to the following layers: LVDS layer, layer formation, power signal and other signal layer. 2.LVDS signal impedance calculation and control. For LVDS signals, must carry on the impedance control (usually the differential impedance control at 100 ohms). For can not control the impedance of the PCB wiring must be less than 500MIL. This is mainly manifested in the connector, so the layout should pay attention to LVDS devices will be placed close to the connector, so that the signal from the device came through a connector to another single board. Also, let the receiving end is also close to the connector, so as to ensure that the noise will not on the board or rarely coupled to the line. LVDS signal voltage swing is only 350 mV, suitable for the current drive differential signal mode. In order to ensure the signal propagation in the transmission line which is not affected by the reflected signal for transmission line impedance controlled LVDS signal, usually differential impedance (100 + 10). The impedance control has a direct impact on signal integrity and delay. How to control the impedance? To determine the line mode, parameters and impedance calculation. LVDS extra layer microstrip differential mode and inner stripline differential mode two, respectively, as shown in Figure 2, shown in figure 3. By reasonably setting the parameters of impedance can be calculated by using relative software (such as POLAR-SI6000, CADENCE, impedance ALLEGRO) can also be c