塑胶制品不良及处理方法（Plastic products, disadvantages and treatment methods）.docVIP

下载本文档

3
0
约1.1万字
约 14页
2017-09-05 发布于河南
举报
版权申诉

塑胶制品不良及处理方法（Plastic products, disadvantages and treatment methods）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

塑胶制品不良及处理方法（Plastic products, disadvantages and treatment methods）

塑胶制品不良及处理方法（Plastic products, disadvantages and treatment methods） Plastic products, disadvantages and treatment methods 2005-3-14 8:27:15 Some of the disadvantages of plastic injection molding machines are in machine performance, mold design, or material characteristics themselves, but most problems are reliably solved by adjusting operating conditions. Adjust the operation must pay attention to: A, change one factor each time, see its result, change another. The whole operating condition must be paid attention to: B, after adjustment, must be observed for a period of time, until the operation is balanced and stable, the results will count. Changes in stress are known in the one or two model, while time, especially temperature, is observed for ten minutes and the results are stable. C, familiar with the possible factors and direction of adjustment of various shortcomings, the following sub item shows the various shortcomings, the possible causes and countermeasures. Some shortcomings and causes are limited to certain reasons, and some disadvantages are the same. 1, incomplete failure reason processing method The raw material temperature is too low to raise the tube temperature Injection pressure is too low to increase injection pressure The amount of melt adhesive is not increasing, measuring stroke The injection time is too short to increase the injection time The injection speed is too slow to accelerate the injection speed Mold temperature is too low to improve mold temperature The mold temperature is uneven, the mold pipe is re adjusted The exhaust of the mould is not proper, and the proper exhaust hole shall be installed in the proper place Nozzle removal, removal, cleaning Unequal opening of mold to re release the mold overflow position The sprue or overflow is too small to enlarge the sprue or overflow The raw material in lubricant and lubricant enough proof Screw check ring (apron), wear, tear down, check, repair The machine lacks enough power to replace t