住宅电气设计概要（Residential electrical design overview）.docVIP

下载本文档

2
0
约1.05万字
约 7页
2017-09-06 发布于河南
举报
版权申诉

住宅电气设计概要（Residential electrical design overview）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

住宅电气设计概要（Residential electrical design overview）

住宅电气设计概要（Residential electrical design overview） Prefabricated box type transformer, capacity not exceeding 630kVA. According to a large number of engineering design practices and examples, summed up 5~7 square meters of residential housing, set up a bureau, substation room, more economical and reasonable. Design of 1.3 substation Substation located in residential buildings, and the distribution of the variable above shall not be located in the household, and just below the adjacent residential building exits on both sides, the bottom should not be located on the ground floor of residential buildings. When there is only one ground floor, the ground elevation 100mm~300mm of the substation should be raised to prevent the ground water from flowing into the substation. The substation should be located in the toilet and bathroom, kitchen or other places are often the water below, and not with the adjacent places. If the adjacent adjacent partition should be no leakage, no condensation water treatment. Change the distribution of the height should be considered the height of equipment in and out line, and should meet the operation and maintenance of the required space requirements, the general distribution device from the top of the slab. (Liang Chuwai) is not less than 0.8m, from beam bottom is not less than 0.6m. Therefore, change the distribution of the beam height should not be less than 3.0m, if needed in low-voltage bus under the beam, the beam height of not less than 3.2m. In practical design, the electricity sector in different regions have their own requirements, such as: the provisions of 6.1.9.1 change the distribution of the net height is generally not less than 3.9m technical specifications for construction of new residential power distribution project of Henan electric power company, if there is a pipeline ventilation equipment or cable channel also need to increase ventilation pipe or cable channel height; Hangzhou residential distribution standards and tech