使用数控冲床的几个技巧（Several skills of using numerical control punch press）.docVIP

下载本文档

2
0
约7.44千字
约 6页
2017-09-06 发布于河南
举报
版权申诉

使用数控冲床的几个技巧（Several skills of using numerical control punch press）.doc

1、本文档共6页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

使用数控冲床的几个技巧（Several skills of using numerical control punch press）

使用数控冲床的几个技巧（Several skills of using numerical control punch press） First, to ensure the best die gap Die gap refers to punch into mould, and the gap of both sides. With the plate thickness, and the material of stamping process, Choose suitable die clearance, to ensure good quality of punching, reduce the burr and collapse, keep sheet formation, effectively prevent with material and prolong the mould life. Through the inspection of ramming waste material, can determine the die gap is appropriate. If the gap is too large, the waste will appear rough and fracture surface and a small bright face. The greater the gap, the fracture surface formation and bright surface of the angle is bigger, punching can be formed when the edge and fracture, and even the emergence of a thin margin. On the contrary, if the gap is too small, the waste will appear small angle fracture surface and large bright surface. When slotting, step punching and shearing part stamping, lateral force will make the punch deflection caused unilateral gap is too small, sometimes edge offset will scratch the lower die, rapid wear caused by the upper and lower die. Die with the best clearance of punching waste, fracture surface and light mask have the same point of view, and overlap, so that the blanking force, punching burr is very small. Two, timely grinding can effectively prolong the service life of the mold If abnormal noise artifacts appear too large burrs or stamping, mold may be dull. Check the punch and die, when the arc edge wear radius is about 0.10mm, to the grinding. Practice shows that often trace grinding rather than wait until the non grinding can not be re grinding, would not only maintain the good quality of the workpiece, reduce the blanking force, but also can make the mold life doubled. Except that when mold grinding, grasp the correct grinding method is especially important. Die grinding procedures are as follows: 1) the use of sintered alumina grinding wheel, hardness D~J, particle size