使用无线路由器后网速变慢的解决方法（How to slow down after using a wireless router）.docVIP

下载本文档

4
0
约6.12千字
约 5页
2017-09-06 发布于河南
举报
版权申诉

使用无线路由器后网速变慢的解决方法（How to slow down after using a wireless router）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

使用无线路由器后网速变慢的解决方法（How to slow down after using a wireless router）

使用无线路由器后网速变慢的解决方法（How to slow down after using a wireless router） Wireless routers are slow to use, which is a small drawback of broadband routers. By measuring the speed of the proof, the installation of broadband router between ADSL access to the computer, on more than one computer at the same time online, due to delay in the router address resolution, routing and other aspects of the actual arrival rate than single computer directly connected to the ADSL line to be slightly slower. Of course, we can also minimize the loss by changing the routers MTU value. MTU is the abbreviation of Maximum Transmission Unit, which means the largest data packet transmitted on the network, in bytes. Different access methods, the MTU value is not the same, if the value is too large, it will produce a lot of packet fragmentation, increasing packet loss rate, reducing network speed. We usually use the broadband PPPoE connection mode, the maximum value of MTU is 1492, the solution is to gradually reduce it until the network is the most normal. So, how do you decide if a MTU value is the best fit? In use, if you have any questions, please add peanut shell 2800th QQ groupGo into the DOS environment (Start all program attachments command prompt) enter the following command line: Ping, -f, -l, 1492, 192.168.1.1. Note: 192.168.1.1 is the gateway IP address (the routers IP, the different routers IP is different, mine is 192.168.18.1), 1492 is the packet length, and the parameter -l is a lowercase L. If there is information: Packet, needs, to, fragmented, but, DF, set, be, that means that the value of MTU is too large! And if there are: Reply, from, 192.168.1.1:, bytes=1492, time10ms, TTL=128, then this MTU value is feasible, but it is recommended to try a few more to find the best value. I tried 1492 to 1260, and finally found the best value: 1260 (this is my Alfa GR50 wireless router, the best value, can be used as reference) now download, web pages, BT and direct access to th