原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
单片机软件复位的方法（Software reset method of single chip microcomputer）
单片机软件复位的方法（Software reset method of single chip microcomputer）
Software reset method of MCS51 Series Singlechip
Date: 2006-03-16: 1 click upload: anonymous source: Internet
Abstract: the article points out a widespread misunderstanding: in the MCS-51 series microcontroller, as long as the instruction is used to start the program from the start of the address, you can reset the microcontroller, get rid of interference. Through a simple experiment, a reliable method of software reset is revealed.
Some SCM (such as 8098) has a special reset command, and some enhanced MCS-51 system microcontroller although no reset instructions, but the chip integrated with the WATCHDOG circuit, so anti-interference is not a problem. And popular MCS-51 series microcontroller (such as 8031 and 8032) since there is no reset instructions, and without hardware WATCHDOS, if there is no external hardware WATCHDOG circuit, you must adopt software anti-interference technology. The common software anti-interference techniques are software trap, instruction redundancy, software WATCHDOG and so on. Their function is to detect the system in time, and then reset the system by software. The so-called software reset is to use a series of instructions to imitate the reset operation, which is the MCS-51 series microcontroller unique software reset technology.
A simple experiment is given to illustrate that the experimental circuit is shown in figure. The light emitting diode LED0, which is connected to the simulation socket P1.0, is used to indicate the work of the main program and then to the P1. The 1 led LED1 is used to represent low-level interrupt routines, followed by P1. The 2 led LED2 is used to indicate the work of advanced interrupt subroutines, followed by P3. The 2 button is used to set up a program to detect interference, interference sign deliberately into the dead cycle or fell into the trap, imitate the interference, in order to test the actual effect of various reduction methods. The in
文档评论（0）