电缆头做法(Cable head practice).doc

  1. 1、本文档共9页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
电缆头做法(Cable head practice)

电缆头做法(Cable head practice) 1 range This process standard is suitable for the installation and installation of indoor PVC insulated PVC sheath and power cable terminal under 0.6/1kV. 2 construction preparation 2.1 material requirements: 2.1.1 cable terminations, plastic belts, wiring noses, galvanized screws, Vaseline cables, cable clips, cable signs, copper wires and other materials must comply with the design requirements, and have the product pass certificate. 2.1.2 plastic belt should be yellow, green, red, black four colors, all kinds of screws and galvanized parts should be galvanized well. 2.1.3 ground wire is made of bare copper flexible wire or multi stranded copper wire. The surface of 25mm2 above 16mm2150 No. 120 should be clean and without strand break. 2.2 main machines and tools: 2.2.1 production and installation tools: crimping pliers, wrenches, hacksaw, file. 2.2.2 test instruments: steel tape measure, shake watch, multimeter, test bell. 2.3 construction conditions: 2.3.1 electrical equipment has been installed and indoor air is dry. 2.3.2 cable laying and finishing, check correct. 2.3.3 cable bracket and cable terminal head mounting bracket are complete. The 2.3.4 site has adequate lighting and spacious operating areas. 3 operation process 3.1 process: Shake the cable insulation: peel off the cable armour, clip the welding wire, the wrapping cable, the sleeve cable, the terminal head, the pressure cable core, the connection nose, and the equipment connection 3.2 shake the cable insulation: 3.2.1 uses 1000V shake meter to test the cable, and the insulation resistance should be above 10M. After the 3.2.2 cable has been measured, the core wires shall be discharged to ground respectively. 3.3 strip off wire armour and clip: 3.3.1 according to the specific dimensions of the cables and equipment, measure the cables and mark them. Cut off the excess cable, cable head size according to requirements, except sheath stripping. The sizes of cable hoods are shown

文档评论(0)

f8r9t5c + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

版权声明书
用户编号:8000054077000003

1亿VIP精品文档

相关文档