胆机耦合电容计算（Calculation of tube coupling capacitor）.docVIP

下载本文档

36
0
约7.44千字
约 6页
2017-10-16 发布于河南
举报
版权申诉

胆机耦合电容计算（Calculation of tube coupling capacitor）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

胆机耦合电容计算（Calculation of tube coupling capacitor）

胆机耦合电容计算（Calculation of tube coupling capacitor） The coupling capacitance calculation - - Amps The formula is actually very simple, C = 318/f, R, F, -1dB, R for the lowest frequency, secondary gate resistor unit is K ohm, if f is set to 10Hz, then the equation is further simplified into C = 31.8/R. Secondary gate resistance 100K, C more than 0.32 micro method 0.33~0.47 micro method 240K, C more than 0.14 micro method 0.16~0.22 micro method 470K, C more than 0.068 micro method 0.068~0.1 micro method 1.0M, C more than 0.032 micro method 0.033~0.047 micro method As we all know, the frequency =1/ cycle, while the cycle =2*3.14*R*C, and therefore: C=1/2*3.14* frequency *R, wherein C is the coupling capacitance capacity, and the R is the input impedance at the next level; The theory on the human ear audible frequency limit is 20Hz, and the OP input impedance can be regarded as infinite, therefore: R= amplifier input resistance value can be calculated by: C=7962/R, general C=8000/R computing (R to C ohmmeter, uF), assuming the grounding resistance R is 20K. So C=0.4uF can; straight to the next level, the pursuit of the input characteristics in low frequency in general, as long as the size and cost of DIYer will allow C to more than two times the value, this is why we see C from 1uF to 10 uF more in OP and stone, and the input capacitance of the power amplifier it is much smaller (especially when the input impedance is relatively large, often only 0.x micro capacitance method), virtually all of them meet the 20Hz replay. Similarly, in the calculation of the amplifier output capacitance is this formula, if the horn, generally 4 ohm to calculate C=2000uF; if 30 ohm headset, C=250uF, then 330uF is a relatively close to the actual value. [em09] Withstand voltage depends on the actual work, capacitors at both ends to withstand the actual DC voltage is how much, if you really want to calculate, but also depends on the value of the AC signal through the capacitor is how much?. Tha