开关电源的pcb设计规范（PCB design specification for switching power supply）.docVIP

下载本文档

4
0
约1.31万字
约 9页
2017-09-27 发布于河南
举报
版权申诉

开关电源的pcb设计规范（PCB design specification for switching power supply）.doc

1、本文档共9页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

开关电源的pcb设计规范（PCB design specification for switching power supply）

开关电源的pcb设计规范（PCB design specification for switching power supply） PCB design specification for switching power supply In any switching power supply design, physical design of PCB board is the last link, if the improper design method, the PCB may be too much radiation electromagnetic interference, caused by the unstable power supply, the following matters for each step needed to pay attention to the analysis: First, from the principle to the design process of PCB based component parameters - input netlist principle design parameters - Settings the layout of manual manual wiring design verification - -CAM review output. Two, parameter setting, adjacent wire spacing must meet the electrical safety requirements, and in order to facilitate operation and production, the distance should be as wide as possible. Minimum distance at least for voltage withstand, the wiring density is low, the signal line spacing can be appropriately increased, the signal line of high level and low level disparity should be as short as possible and increase the distance, will generally go line spacing is 8mil. The distance from the edge of the plate to the edge of the printed plate is greater than 1mm, thus avoiding the defect of the pad when processing. When the line with the pad is thinner, the connection between the pad and the wire is designed to be water drop, so the advantage is that the pad is not easy to peel, but the line and the pad are not easy to break. Three, component layout practice has proved that even if the circuit diagram design is correct, the printed circuit board design is improper, it will also have an adverse impact on the reliability of electronic equipment. For example, if the printed circuit board two thin parallel lines very close, it will form a delay signal waveform, terminal in transmission line form reflection noise due to interference; power supply, wire inconsiderate and cause, will make the product performance decline, therefore, in the design of printed