三菱gps-3电梯故障查询表（MITSUBISHI GPS-3 elevator troubleshooting table）.doc

下载文档 降价啦

19
0
约1.18万字
约 17页
2017-09-26 发布于河南
举报
版权申诉
保障服务

三菱gps-3电梯故障查询表（MITSUBISHI GPS-3 elevator troubleshooting table）.doc

1、本文档共17页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

三菱gps-3电梯故障查询表（MITSUBISHI GPS-3 elevator troubleshooting table）

三菱gps-3电梯故障查询表（MITSUBISHI GPS-3 elevator troubleshooting table） MITSUBISHI GPS-3 elevator troubleshooting table MITSUBISHI GPS - 3 elevator has two switches MON1 and MON0. as long as the rotating the two switches to a different location in the room P1 electronic board. Through the display of letters, in the corresponding Chinese, you can figure out the fault position and the elevator failure time and the number of the 1, MON1 to 0 position, and then MON0 rotation to the 0 position, the display results are as follows E0 has no trouble E1 abnormally low rate detected (SW-TGBL) E2 is too large to check out (SW-TGBH) E3 reversal was detected (SW-TGBR) E4 AST exception detection (SW-AST) E5 inverter over current detection (SS-LOCFO) E6 rectifier over current detection (SS-COVH) E7 rectifier is detected when voltage is low (SS-LVLT) E8 LB coil failure detected during power failure (SW-CFLB) E9 5 coil failure detected during power failure (SW-CFU) EA forced contact ON/OFF fault detection (SW-CFBK) EB car direct signal transmission exception (ST-STSCE) EC out of office and directive direct signal transmission exception (ST-STSHE) ED system exception (ST-SYER) EE drivers are not enabled (SD-DNRS) EF control is not enabled (SW-NRS) I. keep the MON1 unchanged and rotate the MON0 to the 1 position. Show the position of the car and the balance camel. The balance is between 0 and 0. The 1 is equal to 256MM, and the 2 is equal to 512MM Two. Keep the MON1 unchanged and rotate the MON0 to the 2 position. The data is entered, installed, time spent, and used simultaneously with SW1 Three. Keep the MON1 unchanged and rotate the MON0 to the 3 position Four. Keep the MON1 unchanged and rotate the MON0 to the 4 position Five. Keep the MON1 unchanged and rotate the MON0 to the 5 position. Enter the weighing data and use it for maintenance Six. Keep the MON1 unchanged and rotate the MON0 to the 6 position. Manual priority mode Seven. Keep the MON1 unchanged and rotate the MON0 to the 7 posi