电脑平车基本故障维修（Basic maintenance of computer flat car）.docVIP

下载本文档

4
0
约1.1万字
约 11页
2017-09-27 发布于河南
举报
版权申诉

电脑平车基本故障维修（Basic maintenance of computer flat car）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

电脑平车基本故障维修（Basic maintenance of computer flat car）

电脑平车基本故障维修（Basic maintenance of computer flat car） The 1. needle will jump the 1~2 needle The reason: (1) the needle thread is too short, shuttle shuttle presser pressure too strong reduced pressure, to confirm whether the shuttle idling The shuttle spindle is cut short to repair the rotating spindle injury and replace the new rotating shuttle The shuttle shuttle idling thread is pulled into the shuttle shell to strengthen the pressure press and spindle bobbin case tension (2) when sewing, the sewing thread and bobbin are difficult to knot. When sewing the needle, the sewing machine is too fast, the bobbin can not hook to the 1~2 needle, it is changed to slow start (3) rotating spindle tip not Crochet line, machine needle installation method is not correct, the machine needle angle, machine needle bending is new machine needle The front end of the rotating spindle is worn to repair the rotating spindle tip or the new rotary spindle The tension or travel of the spring is too large to reduce tension or reduce travel The time difference between the needle and the shuttle is not good. The needle bar height is determined according to the needle bar line, and the needle rod is slightly lowered in the knitting cloth and the vest step, so that the time is a little bit close (4) the needle, needle plate, press tool is not appropriate, or the press is too light. The needle is too thick, the thinner the needle is, the less the tightness is The needle plate of the needle plate is too big to change into a pinhole small needle board The pressure is too weak to decrease and the feeding force is limited. The screw is strengthened according to the screw of the pressure regulator The pressure foot A size is too large, or the B gap is too large to suppress crack in the space needle, needle plate pinhole parts of the presser feet for too long (5) the thread of the needle is too short after the thread is left in the needle. The cam is too early to check and adjust the cam position The p