数控冲床手动编程（Manual programming of NC punching machine）.docVIP

下载本文档

2
0
约2.02万字
约 23页
2017-10-07 发布于河南
举报
版权申诉

数控冲床手动编程（Manual programming of NC punching machine）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

数控冲床手动编程（Manual programming of NC punching machine）

数控冲床手动编程（Manual programming of NC punching machine） CNC punching manual programming all the code and instructions Reward points: 10 time: 2010-7-15 00:30 | | questionger: you just hate you I operate CNC punching machine! Its from japan! Brand is AMADA, model is ARIES255 ~ expert pointing Best answer Introduction to the NCT directive The NCT program is a digital information file consisting of basic instructions in a certain format. Program writing, fixed format, and a line of NCT programs (a BLOCK) are shown below: N___, G___, G___, X___Y___, T___, C___, M The instructions that are not required for a single command do not have to be entered. The basic format and basic application of the instructions that are common to the NCT program are described below 1. G92 coordinate setting (origin setting) Format G92 X___ Y___ The distance of the material from the origin to the punch position is recorded in the NC device. The origin varies according to the NCT model. The machine tool used in the field is VIP357, and its origin coordinates are X 1830, Y1270. 2. G90 absolute coordinate instruction Format G90 X___ Y___ G90 absolute coordinate instruction, must be recorded before G90. in the absolute coordinate coordinate values if the instruction reads, beginning in G90, then after the BLOCK, can be omitted without writing until G91 before. The procedure without G90 or G91, are considered as the same as G90. 3. G91 relative coordinate instruction The coordinates specified by the G91 command are not calculated from the origin, but rather from the previous hole. The use of this instruction must be entered in the G91. before the coordinate value When the relative coordinate instruction is read, it is initially entered by G91, and the G91 can be omitted and written before the next BLOCK arrives until the G90 appears 4. G50 regression origin command Using the G50 directive, the material returns to the initial state of the NC at the same time as the G92 specified location, and the progr