单片机开发板实习程序.docVIP

#include reg52.h #include absacc.h #define PD1 61 // 122/2 分成左右两半屏(122x32) #define uchar unsigned char #define uint unsigned int #define LEDLen 6 #define mode8255 0x81; sbit speaker = P3^5; sbit FB=P1; sbit D1=P0^0;sbit D2=P0^1;sbit D3=P0^2;sbit D4=P0^3;sbit D5=P0^4;sbit D6=P0^5;sbit D7=P0^6;sbit D8=P0^7; unsigned char timer0h, timer0l, time=0; xdata unsigned char CTL _at_ 0x6003; xdata unsigned char PA _at_ 0x6000; xdata unsigned char PB _at_ 0x6001; xdata unsigned char PC _at_ 0x6002; unsigned char LEDBuf[LEDLen]; // 显示缓冲 code unsigned char LEDMAP[] = { // 八段管显示码 0x3f, 0x06, 0x5b, 0x4f, 0x66, 0x6d, 0x7d, 0x07, 0x7f, 0x6f, 0x77, 0x7c, 0x39, 0x5e, 0x79, 0x71 }; uchar temp,num=0,bzw,m=0,x=0,xh=1,dz=1,zkb,xz=1; uchar k, i, Key; uchar d[6]={0}; uchar num1,num2,shi01,shi02,fen01,fen02,miao01,miao02;//shi1=1,shi2=2,fen1=0,fen2=0,miao1=0,miao2; void delay1(uint CNT) { unsigned char i; while (CNT-- !=0) for (i=110; i !=0; i--); } uchar n; uchar DOTBIT[8]={0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80};//列码 uchar DOTMAP[]= {0x00,0xE7,0x99,0x81,0x81,0x42,0x24,0x18, 0x00,0xE7,0x99,0x81,0x81,0x42,0x24,0x18 }; void Dotmatrix()//点阵显示函数 { uchar i,k=60; while(k--) { for(i=0;i8;i++) { PA=DOTBIT[i];//分列点亮 P1=~DOTMAP[i+n];//送行码 delay1(1); } } } void DisplayLED() { uchar LED,i; uchar a[6]={0x60,0x64,0x68,0x6c,0x70,0x74}; PB=0; //关闭数码管 for (i = 0; i LEDLen; i++) { P2=a[i]; LED = LEDBuf[i]; PB=LED; delay1(5); } } uchar GetKey() { uchar i,j,k[4]={0x70,0xb0,0xd0,0xe0},c; for(i=0;i4;i++) { PC=k[i]; temp=0x01; for(j=0;j4;j++) { if(!(PCtemp)) { if(temp==0x01) { num=1+i;c++;} if(temp==0x02) { num=5+i; c++;} if(temp==0x04) {num=9+i; c++;} if(temp==0x08) { num=13+i;c++; } } temp=1; } } if(c==0){num=0;} else c=0; return num; } uchar GetKey1() { uchar a; a=PC