毕业设计核定生产能力为万吨∕项目改造.docVIP

摘 要 近年来，煤炭行业的发展形势一直很好，越来越多的人力和资金投入到了煤矿的建设和生产中。出于煤炭经济发展的需要和煤矿安全形势的需要，根据国家有关规定要求，小型煤矿必须兼并重组或者进行技术改造提高生产能力。本设计就是在这样的的前提下对鹤壁市大河涧煤矿进行实地考察和实习后，经过认真而详细的分析，计算后撰写的。 该矿原核定生产能力为21万吨∕年，技术改造后生产能力可达到30万吨∕年；该矿开采二1煤，位于山西组底部，煤厚6.2-8.29 m，平均7.47 m，倾角25-380，平均320，煤层稳定，结构简单，普遍可采； 本设计采用立井两水平下山开拓方式，中央并列式通风，井底车场采用卧式车场，立井、暗斜井和采区下山采用提升机提升，大巷采用电机车运输；采用一个工作面和三个掘进工作面保产和接替；工作面采用走向长壁倾斜分层式布置，放炮落煤；工作面采用单体液压支柱和л型钢梁支护顶板，三四排控顶，支柱排距1.0m，柱距0.8m，最大控顶距3.2m，最小控顶距2.4m；回采工作面采用搪瓷溜槽运煤，工作面运输顺槽刮板运输机和可伸缩带式运输机运煤。 关键词：技改 立井　 采区式　走向长壁 分层开采 Abstract In recent years ,more and more manpower and money have been put into the coal mine construction and production because of the good trends .There are also a series of problems , in order to transform the technology and increase the capacity ,small coal mines should be mergers and acquisitions according to relevant provisions of the requirements. The preliminary mine design is for DaHeJiang Mining in HeNan province.Under this design,the output be from 21 to 30 Mt/a. The design is based upon the actual nature term and geology of DaHeJiang at present. The design mainly details upon the development pattern, preparation pattern and mining method and transportation, drainage, hoisting, ventilation and water discharge are also described and calculated for production system. The design adopts the vertical shaft method with two-level up and down to expand the mine plus fully mining method for the whole seam district for preparation. Advanced equipment and technology are at their best utilized in view of present and give a effective measure and for mining safe and good economic. Keywords:Technical transformation ; Shaft;Mining area ; Strike longwall ; Slice mining 目 录 第一章 引言 1 1.1概述 1.2编制设计的依据 1.3指导思想 1.4矿井建设条件评价 1 第二章井田概况及井田地质特征 3 2.1 矿区概况 3 2.1.1位置、交通 3 2.1.2自然条件 4 2.1.3相邻矿井概况 4 2.2 井田地质特征 5 2.2.1地层 5 2.2.2地质构造 6 2.2.3煤层与煤质 7 2.2.4水文地质 8 2.2.5其它开采技术条件 9 2.3 井田勘探程度 9 第三章 矿井储量、年产量及服务年限 11 3.1井田境界 11 3.2井田储量 11 3.2.1地质储量 11 3.2.2矿井工业资源量 11 3.2.3各种煤柱留设原则 11 3.2.4矿井设计资源量