科研大楼施工测量方案.docVIP

目 录 一、编制依据···········································3 二、工程概况··········································3 三、施工测量人员及施工机具配置·······················3 四、施工测量坐标点移交································4 五、施工测量移交坐标点复核···························4 六、施工区内施工测量控制网的布置·····················5 1、施工现场踏勘····································5 2、施工测量控制网的布置····························5 七、施工测量控制网的施测·····························5 八、施工测量控制网的内业计算·························6 九、施工测量控制网的精度评定·························6 1、评定依据········································6 2、精度评定········································6 十、施工测量控制网高程控制··························10 1、施工测量控制网高程控制依据·····················10 2、施工测量控制网高程的施测·······················10 3、施工测量控制网三角高程测量的内业计算···········10 4、施工测量控制网三角高程测量精度评定·············10 十一、施工测量·····································13 1、建筑物定位放线·································13 2、基础工程测量···································13 3、建筑物标高控制·································13 十二、相关附件········································13 1、云南驰宏锌锗股份有限公司研发基地闭合导线坐标测量原始记录表················································13 2、云南驰宏锌锗股份有限公司研发基地闭合导线三角高程测量原始记录表············································13 3、测量员证·······································13 4、测量仪器签定证书·······························13 云南驰宏锌锗股份有限公司研发基地 施工测量专项方案 一、编制依据 依据现场实测数据、施工图纸及《工程测量施工规范》（编号GB50026-2007）。 二、工程概况 1、本工程为云南驰宏锌锗股份有限公司研发基地，位于云南省曲靖开发区中心区，北面为开发区行政部门拟建用地，西面为拟建城市公园，东面为已建的别墅小区，北侧为云南省会城市昆明进入曲靖的主干道，用地南侧为迎霞路，东面为学府路，西有规划路，北临翠峰西路，地势平坦，环境条件优越便利，本工程占地面积约11.81公顷，南北长约403m，北侧东西宽约306m，南侧东西宽约281m。 2、本工程主要由一期项目：1#楼（综合办公楼）、2#楼（会议中心）和二期项目：3#～7#楼（培训中心）及配套用房等子项组成，要求整体规划，分期建设。 3、综合办公楼（1#楼）为高层二类建筑，地下1层，主要功能为车库和设备机房，地上9层，主要功能为办公。 4、研发基地总建筑面积为144267m2，其中一期为40867 m2，二期为103400 m2。 三、施工测量人员及施工机具配置 本工程配备测量工程师1人，专职测量人员1人，辅助测量人员3人。TOPCON GTS-332N全站仪1 套，J2经纬仪1台，DS3水准仪3台。 四、施工测量坐标点移交 在进入施工现场后，由甲方或监理人以书面形式将用于本工程的施工测量坐标点及水准点移交给乙方，由乙方组织专职测量员对所移交控制点进行复核，经复核无误后用于本工程作为施工测量控制。 本工程由甲方或监理人所移交控制点如下表所示： 点号 坐 标 高 程 (m) 备 注 X（m） X（m） K1 2823043.483 500592.190 1872.66 站