技术要求中英对照.docx

SUMMARY OF NOTES技术要求汇总SHEET METAL钣金： NOTES技术要求（喷涂）：INNER BENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注内折弯圆角R_REMOVE ALL SHARP EDGES AND CORNERS 去除毛刺锐边DIMENSIONS ARE TO THEORETICAL SHARP CORNERS尺寸标注为到理论尖角的尺寸FINISH: POWDER COATING表面处理： 喷粉NOTES技术要求（镀锌）：INNER ENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注内折弯圆角R_REMOVE ALL SHARP EDGES AND CORNERS 去除毛刺锐边DIMENSIONS ARE TO THEORETICAL SHARP CORNERS尺寸标注为到理论尖角的尺寸FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面处理：Fe/Zn_ /D (GB/T 9799, ISO20811)NOTES: RECOMMEND Fe/Zn5 /D FOR 120H SALT FOG TEST REQUIREMENT AND Fe/Zn12 /D FOR 192H SALT FOG TEST REQUIREMENT PER ASTM B117.注：对于按照ASTM B117要求，120小时盐雾试验要求的推荐电镀Fe/Zn5 /D，192小时盐雾试验要求的推荐电镀Fe/Zn12 /D. 铜母排COPPER BUSBAR: NOTES 技术要求 (镀锡)： INNER ENDING RADII TO BE R_ UNLESS OTHERWISE SPECIFIED未注内折弯圆角R_；FINISH: BRIGHT TIN PLATING PER ASTM B545按照ASTM B545规定镀亮锡TIN PURITY: 99.0%, GRADE: B BRIGHT, CLASS: B, THICKNESS: 5 TIN PURITY: 99.0%, GRADE: B BRIGHT, CLASS: B, THICKNESS: μm锡纯度：99%， 等级：电镀亮锡， 类型：B， 厚度 μm;OTHER NON PLATING SURFACE TO COVER BY HEAT SHRINKABLE TUBING其余非指定电镀区域用批准的高压热缩套;COPPER CONDUCTIVITY SHALL BE NO LESS THAN 97%IACS 铜导电率不低于97% IACS.NOTES 技术要求(镀银)： INNER ENDING RADII TO BE R_ UNLESS OTHERWISE SPEICIFIED 未注内折弯圆角R_；FINISH: SILVER PLANTING PER ASTM B700表面处理：按照ASTM B700镀银SILVER PURITY: TYPE3 98.0%, GRADE: B BRIGHT, CLASS: N, THICKNESS: 5μm银纯度：3型98%， 等级：亮银B级， 类型：N， 厚度5 μmOTHER NON PLATING SURFACE TO COVER BY HEAT SHRINKABLE TUBING 其余非指定电镀区域用批准的高压热缩套。COPPER CONDUCTIVITY SHALL BE NO LESS THAN 97%IACS铜导电率不低于97% IACS.WELDING 焊装图WELDING TO BE SOLID AND FREE OF VOIDS, SLAG AND VOID WELDING焊缝牢固可靠，无气孔、夹渣和虚焊GRIND AFTER WELDED 焊后打磨 FINISH: PAINT 表面处理：喷漆Or或：FINISH: Fe/Zn_ /D (GB/T 9799, ISO20811)表面处理：Fe/Zn_ /D (GB/T 9799, ISO20811)ASSEMBLY装配图：ALL FASTENERS USED TO BE GB/ISO GRADE 8.8 UNLESS OTHERWISE NOTED所用的紧固件除非特殊说明，强度均为国标8.8级FASTENERS TIGHTENING TORQUE PER SPEC1 - Part B螺栓紧固扭矩按照技术条1 – B部分TO LUBRICANT ON THE RELATIVELY MOVING OR ROTATION PLACES WITH GREASE所有运动部件有相对运动处涂