单片机电子时钟完整程序.docVIP

/* 2键手动奏乐，3键储存报警时间，报警时间到奏乐 1键修改秒的时间，4键修改分的时间，8键修改小时 12键启动定时器开始计数 */ #include reg52.h #include absacc.h //#include SST89x5x4.h #define uint unsigned int #define uchar unsigned char uchar scounter=20; uchar flag=0; uchar i; #define a8255 XBYTE[0x7F00] //8255端口地址定义control 7-LED #define b8255 XBYTE[0x7F01] //send a~g #define c8255 XBYTE[0x7F02] // #define con8255 XBYTE[0x7F03] //unsigned char code table[]={0xfc,0x60,0xda,0xf2,0x66,0xb6,0xbe,0xe0,0xfe,0xf6,0xee,0x3e,0x9c,0x7a,0x9e,0x8e}; //共阴数码管显示编码 unsigned char code table[] = {0x3f, 0x06, 0x5b, 0x4f, 0x66, 0x6d, 0x7d, 0x07, 0x7f, 0x6f, 0x77, 0x7c, 0x39, 0x5e, 0x79, 0x71}; unsigned char b[] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00}; uchar second=0,second_h=0,second_l=0,minute=0,minute_l=0,minute_h=0,hour=0,hour_h=0,hour_l=0; bit dp=0; unsigned char key_down=0; unsigned char key_value=0; unsigned char key_count=0; ///////////////////////////////////////////////// sbit POUT = P3^0; //扬声器控制引脚 //sbit POUT = P0^0; //扬声器控制引脚 #define Clk 0x070000 unsigned char data val_H; //计数器高字节 unsigned char data val_L; //计数器低字节 unsigned char data music_i; //计数器低字节 unsigned int val; uchar Save_Second=61,Save_Minute=61,Save_Hour=25,Save_Flag=0,music_flag=0; //频率表 unsigned int code freq_list[] = {371,495,495,495,624,556,495,556,624, 495,495,624,742,833,833,833,742,624, 624,495,556,495,556,624,495,416,416, 371,495,833,742,624,624,495,556,495, 556,833,742,624,624,742,833,990,742, 624,624,495,556,495,556,624,495,416, 416,371,495,0}; //时间表 unsigned char code time_list[]= {4, 6, 2, 4, 4, 6, 2, 4, 4, 6, 2, 4, 4,12, 1, 3, 6, 2, 4, 4, 6, 2, 4, 4, 6, 2, 4, 4,12, 4, 6, 2, 4, 4, 6, 2, 4, 4, 6, 2, 4, 4,12, 4, 6, 2, 4, 4, 6, 2, 4, 4, 6, 2, 4, 4,12}; void initTimer1() { TMOD|=0X10; TH1 = val_H; //重新装入计数值 TL1 = val_L; EA=1; ET1=1; TR1=1; } void stopmusic() { TMOD=0X01;