北京地铁电动机构造培训.pptVIP

01/01/2007 M40 - Tration motor M40 - 牵引电动机 结束 01/01/2007 M40 - Tration motor M40 - 牵引电动机 Maintenance Training – Specific Presentation 维护培训 - 专场演示介绍 Speed sensor test: 速度传感器测试： Supply the speed sensor with 15 Vdc 为速度传感器供以15V直流的电流 Connect the 2 channels to an oscilloscope (see picture below) 将两通道与示波器相连（参阅下图） Run the motor to 1500 rpm clockwise direction seen drive end. 以驱动端为参考，以1500rpm 的转速顺时针转动电动机。 4) Check that the shift phase and the ovenlap 检查移相和重叠 Check that the conduction time is about 50 % of the period. 检查传导时间为周期的一半 A tolerance of these values is indicated for each type of sensor. 每种类型的传感器都有所列值的相应容差提示 Conduction 传导 Period 周期 Stopped 已停止 Shift 位移 Overlap 重叠 01/01/2007 M40 - Tration motor M40 - 牵引电动机 Maintenance Training – Specific Presentation 维护培训 - 专场演示介绍 Speed sensor values for this motor: 与该电动机速度传感器有关的各数值： Sensor 1: Green cable - Sensor 2: Yellow cable 1 号传感器：绿色电缆 – 2 号传感器：黄色电缆 Teeth wheel: 60 teeth. 齿轮数：60 齿 Speed of the motor: 1500 rprn. 电动机转速：1500rpm Clockwise direction seen drive end. 以驱动端为参考，顺时针方向旋转 Conduction time: 200 Conduction (ms) 450. 传导时间：200 传导 (ms) 450 Phase shift (rising edges S2/S1): 37 Shift (ms) 296 相移（上升缘 S2/S1）：37 相移 (ms) 296 Overlap (rise S1/fallS2): Overlap (ms) 20 重叠（上升 S1 / 下降S2）：重叠(ms) 20 Overlap 重叠 Shift 相移 01/01/2007 M40 - Tration motor M40 - 牵引电动机 Maintenance Training – Tools 维护培训 - 工具 Tools for assembly and disassembly the rotor. The motor is in horizontal position. 用于组装和拆卸转子的工具。电动机处于水平位置。 01/01/2007 M40 - Tration motor M40 - 牵引电动机 Maintenance Training – Tools 维护培训 - 工具 Tools for the extraction of the deflector rep 165 (NDE) 用于拔出偏转器rep 165 (NDE)的工具 01/01/2007 M40 - Tration motor M40 - 牵引电动机 Maintenance Training – Tools 维护培训 - 工具 Special wrench for assembly and disassembly the SKF nut rep 95 用于组装和拆卸SKF螺母rep 95的特殊扳手 01/01/2007 M40 - Tration motor M40 - 牵引电动机 Maintenance Training – Tools 维护培训 - 工具 Tool for the extraction of the deflector rep 145 (DE) 用于拔出偏转器rep 145 (DE)的工具 01/01/2007 M