180万吨1700宽带钢毕业设计.docVIP

摘要  本以武钢1700热轧带钢厂为依据，以包头地区为条件设计一个3/4半连续式轧钢厂，分析了在包头地区建造新的带钢厂的可行性和必要性。建设现代化热轧宽带钢厂要满足现代工业对其产品质量的要求。结合设计条件及年产量要求完成10个产品品种、10个产品规格的产品方案表和金属平衡表。 以钢种为Q235B的初轧坯料轧制宽带钢，典型产品规格为2.4mm×1400mm,并以产品方案表为对象进行了轧机布置型式确定、以及工艺流程的确定，以典型产品为对象进行了压下制度、温度制度、速度制度、轧制压力与轧制力矩的计算。对轧辊强度和轧机主电机进行了校核，并且选择了主要设备和相关辅助设备，进行了各设备性能的参数确定。轧钢机的生产能力和年产量的计算都满足设计要求。并根据本次设计说明完成了CAD车间平面布置图。 关键词：热轧带钢 可行性分析 校核Abstract This design that tack the Tangshan area a condition has designed the annual yield of 1,8 million tons 1700mm new plate factory, analysed the feasibility and necessity of the construction of a new plate factory in Tangshan area. Combined design conditions and the require of annual yield, the design completes seven product varieties, product specifications and metal balance sheet table. A cogged ingot of Q235B is used for the rolling medium plate ,and a typical product specificatons is 2.4mm×1400mm.The design takes the product pian table as the object to form the typical product as the object to calculate the rolling schedule, the temperature system , the speed system, the object to calculate the rolling schedule, the temperature system, the speed system, the rolling pressure as well as the roll torque computation Then ,it check mill roll intensity and the main strength of the electrical capacity , selects the major equipment and auxiliary equipment ,identifies the performance parameters of the equipment .Rolling mill productivity and annual yield of the calculation both meets the design requirements. At last , the CAD workshop layout chart is completed according to the design calculation result. Key words: Hot rolled strip ；Feasibility analysis ；parameter calculation ；Check 目录 I Abstract II 第一章 国内外热轧带钢发展概况及新建热轧带钢厂的必要性与可行性分析 5 1.1国内外热轧带钢发展概况 5 1.2国内热轧带钢厂特点 2 1.3新建热轧带钢厂的可行性与必要性分析 3 第二章 产品方案及金属平衡表的编制 5 2.1产品方案编制 5 2.2产品生产时所需注意的条件 5 2.2.1产品工艺流程的确定 7 3.1 选择轧机时一般要考虑以下各项原则 8 3.1.1 按布列形式轧机的分类 8 3.1.2粗轧机的各种参数 9 3.1.3 保温装置 11 3.2 精轧机 11 3.2.1七架精轧机的确定及选择 12 3.2.2 压下装置 14 3.3确定轧机间距离 及轧机与其他设备的距离 14 3.3.1轧机布