Research and Development on Plasma Facing Components for 在面向组件的等离子体的研究与开发.pptVIP

下载本文档

11
0
约8.91千字
约 18页
2018-04-17 发布于江西
举报
版权申诉

Research and Development on Plasma Facing Components for 在面向组件的等离子体的研究与开发.ppt

1、本文档共18页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Research and Development on Plasma Facing Components for 在面向组件的等离子体的研究与开发.ppt

Japan considerations on design and qualification of PFCs for near term machines (ITER) Satoshi Suzuki1, Satoshi Konishi2 1 Japan Atomic Energy Agency 2 Kyoto University Contents Development / provisional procurement activity of the ITER divertor outer vertical target Small divertor mock-ups Non-destructive examination by using infrared thermography Development of the first wall of the ITER test blanket module (TBM) Provisional high heat flux test of the full-poloidal length TBM first wall mock-up Development of the DEMO divertor Small divertor mock-ups made of ferritic steel with tungsten armor Contents ITER Plasma Facing Components Among the divertor high heat flux components, JAEA is going to procure all of the outer vertical target 22 plasma facing units / 1 cassette 54 cassettes + 6 spares -- 1320 plasma facing units Outer vertical target Design heat flux Tungsten part : 5MW/m2 CFC (Carbon Fiber Composite) part : 10 - 20MW/m2 Coolant condition Water, 4MPa, 100oC Swirl flow by twisted tape (CFC part) Bonding of armor materials Braze HIP (Hot Isostatic Pressing) Prior to the procurement of the vertical target components, the manufacturing process and the thermal performance of the components should be validated/demonstrated by using small mock-ups. (Prequalification activity) Optimization of the manufacturing process by using small mock-ups Armor : CFC (CX-2002U) Tube : CuCrZr Bonding : Brazing (Tbraze=980oC) Ni-Cu-Mn Ti-Cu-Ni Metalizing of CFC Present : Ti-Cu (5 - 10%-Ti) Accuracy of machining of CFC hole +/- 5 microns to the target value High heat flux test has been performed to check the soundness of the braze interface and to demonstrate the thermal performance. High heat flux test of the small mock-upsand fabrication of a qualification prototype Braze filler : Ni-Cu-Mn (980oC x 0.5h, followed by Ar gas quench) Metalizing : Present (Ti-Cu, 7.5 - 10%-Ti) Aging : 475oC x 2h Finally, the mock-up fabricated by using parameters above could withstand the heat